--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@eeaddfdf

spl:mc3: Set TTLOUT1 in SPL

The TTLOUT1 must be set early during boot.

--

Commit: seco-ne/kernel/linux-guf@c725534d

dts:seco-mx6: Rename devicetree subfolder to seconorth

The folder was still named 'garzfricke'.

Change-Id: Ifc6ef2352dcaba5fdfc8b8d9dd1e9156ad83c4c3

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@85526c52

qmlbench: Set nobranch in SRC_URI

The master branch has been renamed/removed from the repository. Since
SRCREV is set to a specific revision there is no need to set a branch
explicitly.

--

Commit: seco-ne/kernel/linux-imx-kuk@b7f2697d

dts:dual-espresso: Remove 100MHz pinctrl for SD Card

Adopt the configuration from EMC test.
In addition, the 100MHz mode causes IO issues with various SD Cards.

BCS 746-001061

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@9982711f

Move deploy jobs to deploy runner

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@a5463b02

kernel:mx8m:defconfig: Add gpio-custom-power-off driver

BCS 746-001083

--

Commit: seco-ne/kernel/linux-imx-kuk@65760c59

dts:dual-espresso: Add custom poweroff routine

The power off routine monitors the PW_FAIL24V# signal. If the 24V
are active or become active again while the system is in the custom
power off routine, a restart is triggered.

BCS 746-001083

--

Commit: seco-ne/kernel/linux-imx-kuk@858faf2e

drivers:psci: Add possibility to skip the assignment of pm_power_off

Since we need a custom poweroff routine for the dual-espresso project,
pm_power_off must be assigned to a special function. pm_power_off is
assigned to psci_sys_poweroff by default. Added a devicetree property
that allows to skip the assignment of pm_power_off to avoid a potential
race condition.

BCS 746-001083

--

Commit: seco-ne/kernel/linux-imx-kuk@f005841e

drivers:power: Add a custom poweroff module for dual-espresso

The module monitors a gpio state and calls the kernel restart
handler when the gpio has a specific state. This done by assigning a
the monitor routine to the pm_power_off function pointer. In this way,
the monitoring starts as the last step of a shutdown -P call.
Devicetree properties:
* init-delay-ms: Set an initial delay until the monitoring is started
* monitor-delay-ms: Poll delay of the gpio

BCS 746-001083

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@e48b4c0b

package_release: Do not fail if a file does not exist

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@a085091f

fng-install: Fix missing output in error cases

Also reduce the minimal size for the FNGSystem partitions needs during
yocto install.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@13b6c687

fng-install: Fix typo

--

Commit: seco-ne/kernel/linux-guf@a14e669b

logo: Removed duplicate of seco boot logo

A duplicate of the seco logo was present in the logos dir.

(cherry picked from commit 348ae9ef8e5439fa62a2d9eceae008bdd5d96348)

--

Commit: seco-ne/kernel/linux-guf@0c15fefb

logo: Enable SECO and FnG logo by default

Both logos need to be enabled by default. The logo that is added to the
kernel is picked through the defconfig and the override in the kernel
include file.

(cherry picked from commit 4dd7c7bbba066a73d06fcafe091e7a46454560d8)

--

Commit: seco-ne/kernel/linux-guf@3991915e

logo: Added fngsystem boot logo

Cherry-pick from af765e15

(cherry picked from commit e03aff3ac82c5aadaa1b755f80074c90a57accda)

--

Commit: seco-ne/kernel/linux-guf@8c6557ad

logo: Added SECO and EDGEHOG logo

Updated the seco logo from the marketing's eps file.

(cherry picked from commit fa277d894d440a993ff24cb93f1a5c94b91fb102)
(cherry picked from commit a70c95c0bac3db1cb2d5c750232bdd2cef634527)

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@260c559e

mx8mp: Add mc3 hdmi backplane devicetree

GitBot authored 2 years ago and Jonas Höppner committed 2 years ago

--

Commit: seco-ne/kernel/linux-imx-kuk@5a2638e5

dts:mc3: Add pcie to dts, mostly copy from evk.

BCS 746-000938

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@296b55fa

seco-show-demo: Adapt systemd service file to kirkstone

Use WAYLAND_DISPLAY variable.
Change logging to journal.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@6ba6cf2f

weston-init: Change path of weston.ini so it is used for mx6 based devices also

The imx override was changed to imx-nxp-bsp before to react on the nxp
overide mechanism, but the imx-nxp-bsp overirde is not set for mx6 based
devices. The seconorth override has higher priority and is available for
all platforms.

BCS 746-001039

GitBot authored 2 years ago and Jonas Höppner committed 2 years ago

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@9b63e87f

tanaro: Add devicetree for Fannal 10.1" display

--

Commit: seco-ne/kernel/linux-imx-kuk@6f218c55

dts:tanaro:Fannal 10.1" display: improve timing, works with SSC now

--

Commit: seco-ne/kernel/linux-imx-kuk@3cc52756

dts:mc3: Enable the internal i2c level translator of the PMIC

Connected ICs:
* Si52202
* ADV7535

BCS 746-000939

--

Commit: seco-ne/kernel/linux-imx-kuk@9d148a43

drivers:regulator:pca9450: Add devicetree property for i2c level translator

The pca9450 has an internal i2c level translator that is disabled by
default. Now the operating modes can be set in the devicetree:
* i2c-lt-en = "force-disable"
* i2c-lt-en = "standby-and-run" - Enable only in STANDBY and RUN mode
* i2c-lt-en = "run" - Enable only in RUN mode
* i2c-lt-en = "force-enable"

BCS 746-000939

--

Commit: seco-ne/kernel/linux-imx-kuk@be4c5701

dts:mc3: Add backplane HDMI support (via ADV7535)

For the ADV7535 i2c connection, the PMIC's i2c level shifter must be
enabled.
Use 12MHz as dsi reference clock rate. This allows the ADV7535 to derive
suitable DDR clock rates. For futher details see:
https://source.codeaurora.org/external/imx/linux-imx/commit/arch/arm64/boot/dts/freescale/imx8mp.dtsi?h=lf-5.15.y&id=5b91a97520cf7479d313c855225caf83e5f3a228

BCS 746-000939

--

Commit: seco-ne/kernel/linux-imx-kuk@cac457dc

dts:mc3:hdmi: Add onboard HDMI support

At the moment there is a problem with the HDMI hot plug detection (HPD)
in combination with the eARC. The HPD only works correctly when
the EARC_N_HPD signal is disconnected. Simply enabling or disabling the
xcvr (eARC) controller does not result in a valid HPD.
HDMI works when the eARC is not connected.
The 5V fault detection is currently not supported.

BCS 746-000949

--

Commit: seco-ne/kernel/linux-imx-kuk@aafa6357

dts:mc3: Enable ml_vipsi gpu node

The node is part of the gpu, but has not been enabled yet.

GitBot authored 2 years ago and Jonas Höppner committed 2 years ago

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@e10430b6

tanaro: Disable display support in defconfig

We don't want to handle the display timings in u-boot as well, and start
the display with the kernel bootlogo instead.

--

Commit: seco-ne/kernel/linux-imx-kuk@1ffbafba

dts:lq057: Updated the pxlclk also for the panel_lvds block

There are two possible ways of using the LVDS panel.
The second block was missing the reduced pixel clock.

See commit c00df0016cf4db916ac429e3c79ef14bead477f0.

--

Commit: seco-ne/kernel/linux-imx-kuk@349ea069

sai:ac97: Replaced timeout message with debug message

--

Commit: seco-ne/kernel/linux-imx-kuk@6ee2a8f1

touch:wm9705: Added infinite mode

The WM9705 can run in a continuous mode, where the conversion channel is
manually switched by writing to register 0x76. This mode is required for a
special touch/codec combination but wasn't supported in the driver yet.
The mode can be activated by adding the "use-infinite-mode" property to the
devicetree node.

BCS 746-001090

--

Commit: seco-ne/kernel/linux-imx-kuk@814db570

wm9705: Added devicetree support for IRQ to the wm97xx

BCS 746-001045

--

Commit: seco-ne/kernel/linux-imx-kuk@34d04b94

dts:mc3: Added 24c64 EEPROM to devicetree

--

Commit: seco-ne/kernel/linux-imx-kuk@1ba1d570

dts:mc3: Added lm75b temperature sensor

--

Commit: seco-ne/kernel/linux-imx-kuk@dc29d0f6

dts:mc3: Added ADC chip to I2C

The ADC chip is detected on the bus but probing fails at the moment.
It seems that the driver tries to send the wrong setup and config bytes
to the chip. Further investigation is required.

BCS 746-001092

--

Commit: seco-ne/kernel/linux-imx-kuk@b33f9429

dts:tanaro: Fix pixel clock and framerate for 10.1 Dataimage SCX1001255GGU06 display

Adapt pixelclock to 71MHz, fixed clock tree.

BCS 746-001034

--

Commit: seco-ne/kernel/linux-imx-kuk@9b958c66

dts:tanaro: Add support for 10.1 Fannal FN1010D013C display

BCS 746-001034

--

Commit: seco-ne/kernel/linux-imx-kuk@89848b5e

seco-mx8mm: Allow to specify the VIDIO_PLL1_RATE as define

This is a bit hacky but currently I don't know a better solution.

Though the doc say assigned-clock-parents may not be used to set clock rates
if there are multiple consumers this is used here widely.
( see Documentation/devicetree/bindings/clock/clock-bindings.txt line 164)
To allow to change this in devicetree using this file, this macro is
introduced, using the default value from before as default.

BCS 746-001034

--

Commit: seco-ne/kernel/linux-imx-kuk@afc2f905

mx8m:sec-dsim: Add message to sec-dsim to print out resulting pixel clock rate

BCS 746-001034

--

Commit: seco-ne/kernel/linux-imx-kuk@b320dc65

seco-mx8mm:tanaro:clk-pll14xx:video-pll1: Add additional setpoint for 700MHz

The pll only has a few preconfigured settings. This adds 700MHz
to achieve additional pixel clocks.

BCS 746-001034

--

Commit: seco-ne/kernel/linux-imx-kuk@8759a147

dts:dual-espresso: Configure touch reset pins as open-drain

The EXC81W32 touch controller tries to reset itself when a touch fwr
update is performed. If the reset pin is driven or configured as
pull-up, the controller gets stuck when the self-reset is performed.

BCS 746-001093

--

Commit: seco-ne/kernel/linux-imx-kuk@c00df001

dts:lq057: Changed to lower clock-frequency

The converter chip for LVDS to LCDIF was changed for the lq057q3dc12.
Reduced the clock frequency accordingly.

GitBot authored 2 years ago and Felix Gerking committed 2 years ago

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@3107ec6f

rng-tools: Omit libjitterentropy

See https://git.toradex.com/cgit/meta-toradex-bsp-common.git/commit/recipes-support/rng-tools/rng-tools_%25.bbappend?id=8146c4e28948e616c1cfdadd5372528757e69abd

The libjitterentropy features are not necessary anymore thus omit the
PACKAGECONFIG for this feature.

BCS 746-001037

--

Commit: seco-ne/kernel/linux-imx-kuk@a27e0e1e

fsl_sai: Fix CONFIG_SND_SOC_FSL_SAI_AC97, build failed without this

--

Commit: seco-ne/kernel/linux-imx-kuk@856b08ff

ucb1400_core: Adapt to AC97_BUS_NEW

--

Commit: seco-ne/kernel/linux-imx-kuk@07c424a8

dts:mc3: Setup SAI to run in AC97 mode

Hint for RX BCLK:
The BCLK (bit clock) is generated by the AC97 codec and routed to TX and RX.
Since we synchronize the incoming BCLK in the SAI, we disable the clock
on RX.

BCS 746-001045

--

Commit: seco-ne/kernel/linux-imx-kuk@9070dbed

fsl_sai: Add AC97 mode for register access

Register the SAI as AC97 controller, setup clocks and format and implement
single register reads and writes.

--

Commit: seco-ne/kernel/linux-imx-kuk@e2955b6a

bus:ac97: Add GPIO reset functions to AC97_BUS_NEW

Added functions to use GPIOs for the AC97 as fallback mode when
the reset call backs of the AC97 controller are not set. The
functionality is based on the implementation of ac97_bus.c.

--

Commit: seco-ne/kernel/linux-imx-kuk@9f808f72

dts:trizeps8plus: Disable VPU

The VPU is currently not working, disable it to enable SW decoding by default.

BCS 746-001087

--

Commit: seco-ne/kernel/linux-imx-kuk@5f217ff8

files: Fixed access permissions of driver files


(cherry picked from commit 3b5b35030b19b27ed4ebcc36eb78c0ed863a528b)

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@a5e27f6e

FTP upload: Add flag to hide FTP upload stage

This is a workaround to prevent customer releases being uploaded to our
public FTP area. It should be removed as soon as we support uploading to
different FTP target folders.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@543a2170

manifest_package: add release suffix

Customer specific manifest projects can now set the RELEASE_SUFFIX
variable, which then gets appended to the deployment folder names.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@c763c43f

alphaplan_fwr: change variable "release_name_local" to "release_name"

Otherwise it can be assumed that it might be correlated with
outputdir_local, which is not the case.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@2d8d26a5

package_release: more refactoring

- Make output-dir an argument that can be passed multiple times instead
  of hard-coding two dirs with certain meanings.
- Remove LOCALDIR variable from package.env, because it is not used
  anywhere (only occurence was job class ".uploadsdkftp" which wasn't
  used anywhere either).

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@dc3698c8

package_release: refactoring

Improve readability of package_release.py and its submodule
generate_release_metadata.py.

- Add describing comments throughout the file.
- Remove duplicate code from functions. Simplify them, so that they do
  what their names say (and nothing more).
- Rename variables and function arguments to make their purpose clearer.
- Harmonize variable names with their corresponding command line arguments.
- Add pydoc for functions.
- Add type declarations to function arguments.
- Generate MD5 and metadata files in the source directories so that they
  can be copied along with the rest of the files.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@ca8dfb5c

qtbase: Add QStylesheetStyle alignment patch

Per customer request add QStylesheetStyle patch form Qt 5.15.4.
See also https://bugreports.qt.io/browse/QTBUG-89366
         https://bugreports.qt.io/browse/QTBUG-86857
         https://codereview.qt-project.org/c/qt/qtbase/+/327897

This patch can be omitted when a later Qt Commercial version is used.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@29c929a2

tests: Add phytool to packagegroup-tests

phytool is used for ethernet compliance tests.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@4467a659

weston:xwayland: Added display for x11

The DISPLAY environment variable must be set for X applications to start
correctly.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@c9ad7470

weston: Fixed auto-start of systemd service

The Weston systemd service was depending on the graphical.target. This target
depends on a display manager which we don't have. Replaced it with the
multi-user.target.

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@9cde740b

kernel:mx8m: Added LED timer trigger

The timer trigger is used for the status LED of the MC3.

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@d1d6c379

kernel:mx8m: Added additional modules for AC97 and WM97XX

BCS 746-001045

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@1330fad5

MC3: Fix missing LPDDR4 RAM setting

During integration of MC3 LPDDR4 RAM settings with 3733 MTS Trizeps RAM
settings for some reason one line of the MC3 RAM settings got lost,
resulting in training for 400 MTS to fail on MC3.

This patch re-insert the missing line. Now MC3 400 MTS training is
working again.

--

Commit: seco-ne/kernel/linux-imx-kuk@c8d34053

dts:mc3: Added status and panic LEDs


(cherry picked from commit 6463eac2dbf78bf830c9da28e1fccb9bc2d09626)

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@96c4fa10

seco-pnmtologo: Add seco-pnmtologo recipe

The seco-pnmtologo tool is a variant of the in-kernel pnmtologo tool.
See also https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/video/logo/pnmtologo.c?h=v5.15.71

The SECO Northern Europe variant adds a binary output mode. The binary
output can be used by the SECO Northern Europe boot logo implementation.

Use oelint-adv to lint the recipe.