The ADC chip is detected on the bus but probing fails at the moment.
It seems that the driver tries to send the wrong setup and config bytes
to the chip. Further investigation is required.

BCS 746-001092

Adapt pixelclock to 71MHz, fixed clock tree.

BCS 746-001034

BCS 746-001034

This is a bit hacky but currently I don't know a better solution.

Though the doc say assigned-clock-parents may not be used to set clock rates
if there are multiple consumers this is used here widely.
( see Documentation/devicetree/bindings/clock/clock-bindings.txt line 164)
To allow to change this in devicetree using this file, this macro is
introduced, using the default value from before as default.

BCS 746-001034

BCS 746-001034

The pll only has a few preconfigured settings. This adds 700MHz
to achieve additional pixel clocks.

BCS 746-001034

The EXC81W32 touch controller tries to reset itself when a touch fwr
update is performed. If the reset pin is driven or configured as
pull-up, the controller gets stuck when the self-reset is performed.

BCS 746-001093

The converter chip for LVDS to LCDIF was changed for the lq057q3dc12.
Reduced the clock frequency accordingly.

BCS 746-001091

Added an optional off state to the panic trigger of the Kernel.
This state can be used to disable other LEDs during a panic condition.

BCS 746-001091

The blinking pattern wasn't correct.
Removed the value from the panic-indicator (only the key is checked).

BCS 746-001091

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

Hint for RX BCLK:
The BCLK (bit clock) is generated by the AC97 codec and routed to TX and RX.
Since we synchronize the incoming BCLK in the SAI, we disable the clock
on RX.

BCS 746-001045

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

Register the SAI as AC97 controller, setup clocks and format and implement
single register reads and writes.

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

Added functions to use GPIOs for the AC97 as fallback mode when
the reset call backs of the AC97 controller are not set. The
functionality is based on the implementation of ac97_bus.c.

The VPU is currently not working, disable it to enable SW decoding by default.

BCS 746-001087

(cherry picked from commit 3b5b3503)

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@a5e27f6e

FTP upload: Add flag to hide FTP upload stage

This is a workaround to prevent customer releases being uploaded to our
public FTP area. It should be removed as soon as we support uploading to
different FTP target folders.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@543a2170

manifest_package: add release suffix

Customer specific manifest projects can now set the RELEASE_SUFFIX
variable, which then gets appended to the deployment folder names.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@c763c43f

alphaplan_fwr: change variable "release_name_local" to "release_name"

Otherwise it can be assumed that it might be correlated with
outputdir_local, which is not the case.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@2d8d26a5

package_release: more refactoring

- Make output-dir an argument that can be passed multiple times instead
  of hard-coding two dirs with certain meanings.
- Remove LOCALDIR variable from package.env, because it is not used
  anywhere (only occurence was job class ".uploadsdkftp" which wasn't
  used anywhere either).

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@dc3698c8

package_release: refactoring

Improve readability of package_release.py and its submodule
generate_release_metadata.py.

- Add describing comments throughout the file.
- Remove duplicate code from functions. Simplify them, so that they do
  what their names say (and nothing more).
- Rename variables and function arguments to make their purpose clearer.
- Harmonize variable names with their corresponding command line arguments.
- Add pydoc for functions.
- Add type declarations to function arguments.
- Generate MD5 and metadata files in the source directories so that they
  can be copied along with the rest of the files.

Felix Gerking authored 2 years ago and Clemens Terasa committed 2 years ago

The SD-Card bus generates EMI problems for higher Bus frequencies. Thsus
limit the SD-Card bus to 50MHz.

From our expectations this should mean, that DDR50 is available.
See also https://en.wikipedia.org/w/index.php?title=SD_card&oldid=1112713978#Power_consumption

In the drivers/mmc/host/sdhci-esdhc-imx.c driver, however, the DDR50 is
only advertised when the pinctrl state_100mhz is available.

Felix Gerking authored 2 years ago and Clemens Terasa committed 2 years ago

* Added pin muxing for the default, 100MHz and 200MHz speeds
* Set drive strength to DSE_X1 for default and DSE_X2 for 100/200 MHz

Tobias Kahlki authored 2 years ago and Tobias Kahlki committed 2 years ago

(cherry picked from commit 6463eac2)

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@c831d1da

get_integration_sources: check if CI is enabled

Trying to query CI variables on a project which does not have the CI
feature enabled leads to an HTTP 403 (forbidden) error.
Check whether CI is enabled using the "jobs_enabled" flag.

Enabled the 2D/3D GPUs and the various VPUs on the i.MX8MP.

BCS 746-001060

BCS 746-000942

Tobias Kahlki authored 2 years ago and Tobias Kahlki committed 2 years ago

The backlight PWM period was wrong which prevented the display from
dimming correctly.

BCS 746-000948

Set Rp to 330uA to advertise 3A at 5V in host mode.

BCS 746-000948

The properties can be set optionally in the devicetree. If one is set,
the control reg of the ptn 5051 is adjusted accordingly via i2c at the end
of the probing routine. This allows to override the initial configuration
which is applied during power up.

Rp: Advertises the allowed current in host mode
mode: UFP, DFP or DRP

BCS 746-000948

After driver customizations we can use the usb-role class scheme to
enable the otg mode.

BCS 746-000948

The previous probing order let to an irq: type mismatch error when
deferred probing is required. This is due to the fact that some
interrupt assignments already take place before probing is cancelled.
Now the usb_role_switch_get function is moved before the interrupt
assignments to cancel if the usb driver is not ready yet.

BCS 746-000948

Li Jun authored 2 years ago and Felix Gerking committed 2 years ago

Some usb controller drivers may not support extcon but use
usb role class as it's the preferred approach, so to support
usb dual role switch with usb role class, add usb role class
consumer support.

Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Li Jun authored 2 years ago and Felix Gerking committed 2 years ago

Add device managed action to sync pending queue work, otherwise
the queued work may run after the work is destroyed.

Fixes: 4ed754de ("extcon: Add support for ptn5150 extcon driver")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@5e3dfaea

CI:deploy: fix fngsystem deployment path

The match to detect fngsystem still contained 'guf'. Changed to 'seco'.

BCS 746-001043

The lq057q3dc12 runs with a jeida-24 data mapping.

BCS 746-000951

Added an optional node with panel-dt settings for the
lq057q3dc12.

BCS 746-000951

We use a custom Simple Panel driver that allows a more detailed description of
panels in the device tree. This is discouraged by the mainline kernel but has
shown useful for our specific applications.

For a more detailed explanation see the discussion https://patchwork.kernel.org/
project/dri-devel/patch/20190307101030.3822-1-maxime.ripard@bootlin.com/ on
the DRI mailing list and the original commit https://git.seco.com/seco-ne/
kernel/linux-guf/-/commit/bc113aef63149d38a61f618b40f91e22d53fe5cd on the i.MX6
kernel.

Note: Replaced all occurences of the old G&F name to SECO and also fixed
some smaller typos.

BCS 746-000951

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@f8d6de86

Make check error message more verbose

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@21e7edeb

Improve ci-test build

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@76bd81d8

Fix check job rules

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@a6721243

Move check job to parent pipeline

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@593784e1

Refactor check_if_integration_branch_is_up_to_date

- Use "source" and "target" terminology in the script, just like in the
  GitLab CI variables.
- Spefify data types for function arguments.
- Rename function arguments to better reflect their data types.
- Move determination of integration branch into main function, so that
  the successfull status message can be more verbose.
- Remove parent_merge_request feature and checking for gitlab-ci
  integrations, because the check job does not run on gitlab-ci
  integration branches at all.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@45b49ee3

Remove build stage on master

We don't need to explicitly trigger a build after merging changes in
gitlab-ci. A master pipeline on the target projects runs automatically.