--

Commit: seco-ne/kernel/linux-guf@ffcfe481

arm:dts: Moved muxing of EN_VBAT to generic SANTVEND out group

The pin muxing wasn't loaded correctly.

--

Commit: seco-ne/kernel/linux-imx-kuk@047033f8

dts:mc3: Fixed reset polarity of GPIO-Expander

The polarity of the reset is active high.

--

Commit: seco-ne/kernel/linux-guf@7d439e13



panel-dt: Add handling of "sel6_8_polarity" property in device tree

Add support of optional "sel6_8_polarity" property to device tree,
which defines the polarity of the "sel6_8" gpio pin. Because some panels
(such as Kyocera TCG070WVLQ-AN*174) need "sel6_8" signal to be inverted
for proper operation.

Signed-off-by: Dmitry Petrov <dmitry.petrov@rtsoft.de>

--

Commit: seco-ne/tools/gfxml2dto@7ee50f01



dto: panel: Add "sel6_8_polarity" property

Add support of "sel6_8_polarity" node to the panel fragment of device
tree. This property is handled by "panel-dt" driver to set the polarity
of "sel6_8" gpio pin. The naming is inherited from corresponding XML
files used by gfxml2dto.

Signed-off-by: Dmitry Petrov <dmitry.petrov@rtsoft.de>

--

Commit: seco-ne/kernel/linux-guf@8cd96a28



arm:dts:san: fix i2c1 gpio numbers

scl-gpios and sda-gpios were mixed up with each other.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@cdfc7012

packages:libs: Added libmodbus to connectivity

BCS 746-001362

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@5a1e0f0e

machine:mx8mp: Added MC3 v1r0 DT

The revision was wrong because of a failed integration.

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@71ff8334

uboot:dts: add pull-up for SAI1_TXD1 and tidy up other boot pin configs

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@0da7c2ef

uboot:board: propagate board and module info to environment during boot

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@2ff9b17e

uboot:board: improve boot output describing the system

This commit uses the new baseboard detection to make the descriptive
output during boot ("This is a...") more meaningful.

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@703075a3

uboot:cmd: refactor guf command

This commit removes all code which was previously used to detect the
board, as this functionality was moved to
board/keithkoep/common/baseboard*. Only code with the purpose to do the
bootmode detection remains.

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@edeaf423

uboot:board: add generic platform and baseboard revision detection

This commit implements generic platform and baseboard revision detection
for SBC and SOM systems. It currently supports PFID based baseboard
detection.

- baseboard.h: common interface to query baseboard type and revision. It
  defines the board types, detects whether PFIDs are used or some other
  system and forwards the calls to the proper implementation.
- baseboard_pfids.h: type and revision detection using PFIDs
- baseboard_util.h: utility functions for reading GPIO values

Some additional functions were made available in kuk_boards.h to
implement the changes.

--

Commit: seco-ne/3rd-party/kuk/uboot-imx-kuk@054cf0b7

uboot:config: enable OF_LIBFDT_OVERLAY config option

This change is required to make the fdt apply u-boot command available
which is used for applying device tree overlays.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@a35910ae

packages:tests: Moved Qt tests to packagegroup-seconorth-qt

The Qt tests in the general tests packagegroup trigger a full Qt build (even
for images and distros that don't include Qt). This leads to unnecessary long
build times. Moved the tests to the Qt packagegroup, to ship
around this issue.

--

Commit: config@5e794fde

setup: exit setup script correctly regardless of how it was called

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@880d976a

qtbase: Add package config ICU

Decoding the xml files that used "encoding='ASCII' " did not work
anymore because of the missing feature.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@37c824f7

video: Add symlinks for dma_heap nodes if the cma size is specified by cmdline

By default libimxdmabuffer (required for vpu video playback) expects
the cma heap nodes to be available at /dev/dma_heap/linux,cma and
/dev/dma_heap/linux,cma-uncached respectively.
These nodes are only created when the devicetree cma declaration is used.
Add a udev rule that creates symlinks if the cma size is specified by
kernel cmdline.

BCS 746-001325

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@5ec287ec

classes: Add class for Wic image creation

The class sets all variables to create and deploy a wic.gz image with
SECO North default partition layout.

BCS 746-001176

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@34aff3be

wic:wks:mx8: Add a wks file for the default partition layout

The partion layout is based on the default layout, so that it can be
reused by the fng-install scripts. At the moment the partition sizes
are hardcoded for 4GB SD-Cards or eMMCs. To set up the boot and rootfs
partitions the seconorth-boot and seconorth-rootfs Wic plugins are
required. Currently only mx8 machines are supported.

BCS 746-001176

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@8615b8ae

wic:plugins: Add seconorth-rootfs Wic plugin

The plugin in based on the rootfs plugin of the poky layer.
In contrast to the rootfs plugin, the plugin modifies the fstab file
to mount the boot partition by uuid. In this way, label conflicts are
resolved when installations are present on an eMMC and an SD card at
the same time.

BCS 746-001176

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@6a6cf35b

wic:plugins: Add a Wic plugin for to customize the boot partition

The plugin in based on the bootimg-partition plugin of the poky layer.
In contrast to the bootimg-partition plugin, the artifacts are copied
from the image rootfs/boot folder. In the boot.cfg file the kernel and
rootfs parameters are set. The corresponding rootfs device is
determined from the current value of the WIC_ROOTFS_DEVICE variable.

BCS 746-001176

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@a9fa3cdc

core:ro-overlay: Added workaround for machine-id

The machine-id is shadowed by the overlay. Since it is required by some
services, a temp. workaround was added.

BCS 746-000813

--

Commit: seco-ne/kernel/linux-imx-kuk@2d9b37d0

arm64:dts: Re-enable VPU on tanaro and trizeps8plus

In user space, the CMA buffer nodes are now handled correctly, so
video playback works now.

BCS 746-001325

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@fb74bceb



imx-lib: switch to the NXP repo on github.com

Changed NXP source URL from codeaurora.org to github.com as NXP moved
all repositories to github.com. codeaurora.org is already offline.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@c70ce5ee

core:ro-overlay: Added detection of bootdevice

Added a detection for the bootdevice to the ro-overlay script.
This is required when booting from a SD-Card.

BCS 746-000813

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@89134541

packages:uboot: Moved libubootenv-cfg to optional dependencies

The package can't be removed in the image as intended. Moved it to the
RRECOMMENDS to fix this.

BCS 746-000813

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@258378d7

packages:small: Reverted ro changes for the U-Boot tools

The read-only-rootfs check doesn't work in the packagegroup.
Reverted the changes to the U-Boot recipes.

BCS 746-000813

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@f1422f67

conf:mx8m: Set IMX_BOOT_SEEK var for mx8mp and mx8mm machines

The variable is used when creating Wic images.

BCS 746-001176

--

Commit: seco-ne/kernel/linux-imx-kuk@678f7c35

ucb1400 touch: fix exception at boot and allow disabling of pressure

This patch fixes the exception/warning regarding imbalanced enable_irq()
and adds a globbal variable to allow disabling of pressure measurements.
Currently pressure measurements are still enabled, though, because in
current state the touch behaves even worse with pressure disabled.

--

Commit: seco-ne/kernel/linux-imx-kuk@cc51fd1a

dts:mc3: Added UCB1400

Added the UCB1400 codec to the SAI of the MC3.

BCS 746-001152

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@1c2d3a37

uboot:tools: Fixed wrong check

The utils.contains must check the IMAGE_FEATURES variable.
The IMAGE_FEATURES already contains the EXTRA_IMAGE_FEATURES.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@cc27affe

sharedconf:network: Enable systemd network service by default

The service checks if a valid network configuration is present. If no
config was found, a new one is generated.
The configuration is based on the content of the sconfig file.

BCS 746-000813

--

Commit: seco-ne/kernel/linux-imx-kuk@7f7e71a3

dts:mc3: Added ADV_PD and ADV_INT GPIO names

BCS 746-001077

--

Commit: seco-ne/kernel/linux-imx-kuk@a79800f1

dts:aarch64:mc3: Enable PD signal of ADV7535 by default

The ADV7535 should have high impedance outputs, when HDMI on the
backplane is not used. Add a gpio-reset for the PD pin and set it to the
initially-in-reset state. Only if the hdmi-backplane-mc3.dtsi file is
included, this property is removed.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@df809262

core:helper: Added read-only-rootfs overlay helper

BCS 746-000813

--

Commit: config@33677ded

setup: actually exit when being run as root

--

Commit: config@466b8cfb

setup: Replaced return with exit

The return statements didn't exit the script correctly which led to an
infinite loop when calling the script with the help parameter.

--

Commit: seco-ne/tools/gf-emc-test-suite@08842749



bball: fix multiple definition linking error

Build fails with following errors:
ld: git/testcases/bball/tga_reader.h:34: multiple definition of
`TGA_READER_ABGR'; git/testcases/bball/tga_reader.h:34: first defined here
ld: git/testcases/bball/tga_reader.h:33: multiple definition of
`TGA_READER_ARGB'; git/testcases/bball/tga_reader.h:33: first defined here

Add extern to those definitions in header file.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/kernel/linux-imx-kuk@eb328a82

fsl_sai: disable irqs during AC97 register access

If interrupts occur after enabling the SAI RMR but before enabling the SAI TMR during AC97 read register accesses, the FIFO can run full of empty frames and we are not able to receive the expected answer from the codec. Therefore this patch disables IRQs for the current CPU during this critical step.

BCS: 746-001295

--

Commit: config@3830d2fa

bblayers, setup-environment: Add support for seco-mx6-fsl reusing the bblayers_mx8

setup-environment: rename bblayer variants from soc to functionality postfix

Remove the soc type from the bblayer variants and use _fsl in one to
describe the functionality.
Implement the mapping in the setup-environment script more expressive.

--

Commit: seco-ne/yocto/infrastructure/gitlab-ci@23680f48

Fix check for branch protection state

Since the changes of 939ade2b9f98b3e1569332270a7ab16ce7d70b4a we observe
that pipelines are executed on non-protected branches, which is not what
we want.

GitLab's documentation was a bit unclear on the according CI variables
CI_COMMIT_REF_PROTECTED and CI_MERGE_REQUEST_TARGET_BRANCH_PROTECTED, as
stated in this stack overflow answer:
https://stackoverflow.com/a/59023344/3018229

We need to explicitly check for the variable values to be "true" instead
of just checking whether they are set.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@6f0d86cd

uboot:tools: Disabled post-install config check

The check doesn't work together with the read-only-rootfs feature. Since the
read-only-rootfs is mostly used on new devices, the check shouldn't be
necessary.

BCS 746-000813

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@a8704213

image:prepare: Moved the network conf to the prepare-image step

Generating the network configuration upon the first boot doesn't work for
read-only filesystems. Since we generate the network config only during the
first boot after an installation, the step was moved to the post-install steps
of the fng-install script.

BCS 746-000813

--

Commit: seco-ne/tools/gfxml2dto@4c5c76e0



main: add -f argument

If -f argument is provided, fsl flag will be set to true to config.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/tools/gfxml2dto@33884991



dto: select functions based on fsl boolean flag

If fsl flag is true, overlays will be created for nodes from NXP kernel.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/tools/gfxml2dto@a88c7fba



guf_xml_config.h: add fsl boolean flag for guf_xml_data struct

It will be used to select which functions will be used to create overlays
for LVDS related nodes.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/tools/gfxml2dto@e2dddaee



dto: add functions to add lvds related overlays for fsl based imx6 dtb

Functions are based on guf_xml_to_dt.c from linux-imx-4.1.15 from Jethro BSP.

Signed-off-by: Mikhail Vanyulin <mikhail.vanyulin@rtsoft.de>

--

Commit: seco-ne/tools/secure-element-examples@ab59e351

CI: Add gitlab-ci files to the repository

--

Commit: seco-ne/kernel/linux-imx-kuk@f3fffaa5

fix AC97 read timeouts

Previously we see AC97 read register calls timing out every once in a
while. Adding some debug outputs, these mostly seem to be cases, where
the SAI driver doesn't find the expected answer in the received frames.

Three potential causes have been identified:
 * frame "border" occuring exactly between enabling RMR and TMR,
 resulting in receiving an additional empty RX frame (4 instead of 3)
 until the answer arrives
 * kernel preemption between RMR and TMR resulting in potentially lots
 of empty frames accumulating in the RX-FIFO
 * runnig in a timeout, because the code gave up after 63us already (3
 frames), although due to the asynchronous timing we might have to wait
 up to almost 104us (5 frames)

This patch adds fixes for all three cases. During first manual tests no
more timeouts could be produced.

BCS: 746-001295

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@c73a769d

Switch to the NXP repos on github.com

Changed NXP source URLs from codeaurora.org to github.com as NXP moved
all repositories to github.com. codeaurora.org is already offline.

--

Commit: seco-ne/yocto/layers/meta-seconorth-machine@4a8c4ac5

u-boot:scripts: Clean-up of boot config and scripts

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@db68ce5b

security: Move se05x-aes-key example to its own repo

The se05x-aes-key example is now available in a separate repository.

--

Commit: seco-ne/yocto/layers/meta-seconorth-distro@dfcb0a9e



security: build plug&trust MW mini package as shared library

Split the example to another recipe that requires the mini package to be
build as shared library. This would also allow us to integrate the mini
package into the sdk, allowing costumers to access the secure element
from their software.

Signed-off-by: Dmitry Petrov <dmitry.petrov@rtsoft.de>