The image file for the fngsystem boot logo was missing.
Re-added the file to fix the kernel build.

Both logos need to be enabled by default. The logo that is added to the
kernel is picked through the defconfig and the override in the kernel
include file.

Cherry-pick from af765e15

Felix Gerking authored 2 years ago and Tobias Kahlki committed 2 years ago

Added wakeupsource and interrupt for RTC rv3028.
Now wakealarm the is available at: /sys/class/rtc/rtc0/wakealarm

BCS 746-000767

(cherry picked from commit a72cb6a2)

Jonas Höppner authored 3 years ago and Tobias Kahlki committed 2 years ago

Measured the pixelclock on the lvds interface the frequencies generated
by media_dips2_pix clock do not match the calculated values by the
driver. The driver selects a devider between 1 and 64 ( according to the
    ref manual) but the measured frequencies only end up with
frequencies matching a devider from 1,7,14,21,35.
This patch changes the selected of deviders to that list, so the
frequency is rounded to a actually working frequency.

BCS 746-000495

(cherry picked from commit 70382bea)

Jonas Höppner authored 3 years ago and Tobias Kahlki committed 2 years ago

The imx8mp ldb driver had an hardcoded overwrite for the pixelclock as
the video_pll is not able to generate all needed frequencies.
But the hardcoded value only fits to one mode, probably used on the
EVK.
Removing this override leads to a pixelclock that may be generated with
a devider from the PLL, which ends up with a frquency much closer to what
is expected.

Also it is not the ldb clock but the lcdif clock used for this, so this
seems to be the wrong place for modifying the clock anyway.

BCS 746-000502

(cherry picked from commit 86df943d)

Felix Gerking authored 2 years ago and Tobias Kahlki committed 2 years ago

The pwm-legacy-backlight driver is removed in the 5.15 kernel. Use
pwm-backlight instead.

BCS 746-001009

For some reason, without the hdmiphy the device stalls during the boot
process. Further investigation into why this happens is required.

BCS 746-001009

The ethernet phy and audio codec have changed in the new revision of the
Trizeps 8 Plus. Removed the unwanted properties from the ethphy0 node
and set the address to 0.
The audio codec hasn't been added yet.

Cherry-pick from a40f7a72

BCS 746-000835

Changed the driver to probe without interrupt gpio, as the irq is not
routed on the trizeps8plus board. It seems to be used for debug output
on pmic errors only, so it should work without.

Cherry-pick from 7739e8c9


(cherry picked from commit 3ec08c4d)

The first approach of selecting a RTC didn't work as expected.
The active RTC must reside on the rtc0 alias because otherwise
the hwclock utilities can't access the RTC.
For this to work, we now have a placeholder in the main device tree
that is filled with the actual values in one of the two overlays.
This breaks with the naming conventions for I2C bus devices, but
right now, we don't have a better solution.

BCS 746-000877

(cherry picked from commit 11963a85)

The TANARO will be produced with one of two RTC variants.
One of them will be activated during the installation by
applying one of the overlays.

BCS 746-000877

(cherry picked from commit 9b1710b2)

Replaced imx8mp-pinfunc.h and imx8mp.dtsi with the files provided
with the 5.15 kernel.

Our devicetrees reside in the seconorth sub-directory.

Added missing devicetree include and added the new devicetrees
to the Makefile.

The devicetrees and includes have been copied from the
linux-5.10.9-guf branch.

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

The enable gpio was used as enable pin and additionally configured as
enable for a regulator. The duplicated usage was not allowed and made
the driver probe fail. For now the tas2552 driver controlls the enable
gpio, which is also only half correct, as the MIC supply is also
controlled with this pin.

Updated the seco logo from the marketing's eps file.

(cherry picked from commit fa277d89)

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

Reparent mipi to also use the VIDEO_PLL1 so it is also uses spread
spectrum when SSC is enabled on this PLL.

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

Rename display enable to lcd enable and remove defines from
tanaro_pinfunc.h

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

When the probe function returned -EPROBE_DEFER the second call to the probe
failed because the resets couldn't be acquired a second time.
This releases the resets in case of error, so the second call to probe
is able to get the resets.

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

The rohm bd71847 driver refuses to start without irq setup.
As the line is connected to a gpio, I added the definitions to the
devicetree.

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

During boot with pcie enabled, the output stops in the pcie
initialization. Removed for now.

Jonas Höppner authored 2 years ago and Tobias Kahlki committed 2 years ago

Copy the files from the 5.10 kernel, except
for imx8mm.dtsi and imx8mm-pinfunc.h which come
from the freescale devicetree directory in the 5.15 kernel.

It seems that there are circumstances when access to QBMAN through the
software portals will be delayed. Accessing some lower speeds interfaces
while also QBMAN commands are issued from the kernel will lead to
software timeouts happening in the dpaa2-eth driver.

What we have observed is that management commands like re-arming the
interrupts on a specific channel, waiting for a dequeue response to be
available etc, will take a longer time to complete.
All these commands have to wait for a valid bit to be set for the
command to be interpreted as successfully completed.

Increase the maximum number of times the Linux kernel drivers will busy
poll for a successful result of one of these commands.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>

Enable CONFIG_SFP for the Linux SFP infrastructure. Also, enable the
Lynx 28G SerDes PHY driver which supports runtime reconfiguration of
SerDes lanes.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>

There is a downstream patch which adds a new interface type -
PHY_INTERFACE_MODE_2500SGMII (which is really the same one as
PHY_INTERFACE_MODE_2500BASEX).

We backported from upstream the following phylink patch which, of
course, does not treat the PHY_INTERFACE_MODE_2500SGMII interface mode
in a switch case statement.
	34ae2c09 ("net: phylink: add generic validate implementation")

Because of this, we get the following build warning.

drivers/net/phy/phylink.c: In function ‘phylink_get_linkmodes’:
drivers/net/phy/phylink.c:322:2: warning: enumeration value ‘PHY_INTERFACE_MODE_2500SGMII’ not handled in switch [-Wswitch]
  322 |  switch (interface) {
      |  ^~~~~~

Fix it by treating the new interface mode in the switch-case statement.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>

This reverts commit 6809b4d8.

The patch causes kernel crashes on DPAA2. Revert the changes and
reimplement at a later time.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>

Since the blamed commit, VCAP filters can appear on more than one list.
If their action is "trap", they are chained on ocelot->traps via
filter->trap_list. This is in addition to their normal placement on the
VCAP block->rules list head.

Therefore, when we free a VCAP filter, we must remove it from all lists
it is a member of, including ocelot->traps.

There are at least 2 bugs which are direct consequences of this design
decision.

First is the incorrect usage of list_empty(), meant to denote whether
"filter" is chained into ocelot->traps via filter->trap_list.
This does not do the correct thing, because list_empty() checks whether
"head->next == head", but in our case, head->next == head->prev == NULL.
So we dereference NULL pointers and die when we call list_del().

Second is the fact that not all places that should remove the filter
from ocelot->traps do so. One example is ocelot_vcap_block_remove_filter(),
which is where we have the main kfree(filter). By keeping freed filters
in ocelot->traps we end up in a use-after-free in
felix_update_trapping_destinations().

Attempting to fix all the buggy patterns is a whack-a-mole game which
makes the driver unmaintainable. Actually this is what the previous
patch version attempted to do:
https://patchwork.kernel.org/project/netdevbpf/patch/20220503115728.834457-3-vladimir.oltean@nxp.com/



but it introduced another set of bugs, because there are other places in
which create VCAP filters, not just ocelot_vcap_filter_create():

- ocelot_trap_add()
- felix_tag_8021q_vlan_add_rx()
- felix_tag_8021q_vlan_add_tx()

Relying on the convention that all those code paths must call
INIT_LIST_HEAD(&filter->trap_list) is not going to scale.

So let's do what should have been done in the first place and keep a
bool in struct ocelot_vcap_filter which denotes whether we are looking
at a trapping rule or not. Iterating now happens over the main VCAP IS2
block->rules. The advantage is that we no longer risk having stale
references to a freed filter, since it is only present in that list.

Fixes: e42bd4ed ("net: mscc: ocelot: keep traps in a list")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit e1846cff)
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>

This reverts commit 8146e2b6. It was
fixed differently upstream, we'll use that.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>

This reverts commit 0e9c8bdf. This was
fixed differently in upstream, we're going for that approach.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>

Downstream commit bbd95975 ("selftests: ocelot: tc_flower_chains:
reorder interfaces") got merged upstream as 93196ef9 ("selftests:
ocelot: tc_flower_chains: use conventional interface names"), with the
difference that interfaces are ordered differently and traffic flows in
the other direction.

Eliminate this difference by copy-pasting the upstream version of the
selftest.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>