Bit 2 of the mode byte has dual meaning: it can disable reporting of
gestures when touchpad works in Relative mode or normal Absolute mode,
or it can enable so called Extended W-Mode when touchpad uses enhanced
Absolute mode (W-mode). The extended W-Mode confuses our driver and
causes missing button presses on some Thinkpads (x250, T450s), so let's
make sure we do not enable it.

Also, according to the spec W mode "... bit is defined only in Absolute
mode on pads whose capExtended capability bit is set. In Relative mode and
in TouchPads without this capability, the bit is reserved and should be
left at 0.", so let's make sure we respect this requirement as well.

Reported-by: Nick Bowler <nbowler@draconx.ca>
Suggested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

GPIOF_IN flag was lost in:
Commit 633a21d8("input: gpio_keys_polled: Add support for GPIO
descriptors").

Without this flag, legacy code path (for non-descriptor GPIO declarations)
would configure GPIO as output (0 meaning GPIOF_DIR_OUT | GPIOF_INIT_LOW).

Cc: stable@vger.kernel.org
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It is no need to check the packet[0] for sanity check when doing
elantech_packet_check_v4() function for fw_version = 0x470f01 touchpad.

Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix following:
[    8.862274] ERROR: Bad of_node_put() on /ocp/i2c@48070000/twl@48/audio
[    8.869293] CPU: 0 PID: 1003 Comm: modprobe Not tainted 4.2.0-rc2-letux+ #1175
[    8.876922] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[    8.883514] [<c00159e0>] (unwind_backtrace) from [<c0012488>] (show_stack+0x10/0x14)
[    8.891693] [<c0012488>] (show_stack) from [<c05cb810>] (dump_stack+0x78/0x94)
[    8.899322] [<c05cb810>] (dump_stack) from [<c02cfd5c>] (kobject_release+0x68/0x7c)
[    8.907409] [<c02cfd5c>] (kobject_release) from [<bf0040c4>] (twl4030_vibra_probe+0x74/0x188 [twl4030_vibra])
[    8.917877] [<bf0040c4>] (twl4030_vibra_probe [twl4030_vibra]) from [<c03816ac>] (platform_drv_probe+0x48/0x90)
[    8.928497] [<c03816ac>] (platform_drv_probe) from [<c037feb4>] (really_probe+0xd4/0x238)
[    8.937103] [<c037feb4>] (really_probe) from [<c0380160>] (driver_probe_device+0x30/0x48)
[    8.945678] [<c0380160>] (driver_probe_device) from [<c03801e0>] (__driver_attach+0x68/0x8c)
[    8.954589] [<c03801e0>] (__driver_attach) from [<c037ea60>] (bus_for_each_dev+0x50/0x84)
[    8.963226] [<c037ea60>] (bus_for_each_dev) from [<c037f828>] (bus_add_driver+0xcc/0x1e4)
[    8.971832] [<c037f828>] (bus_add_driver) from [<c0380b60>] (driver_register+0x9c/0xe0)
[    8.980255] [<c0380b60>] (driver_register) from [<c00097e0>] (do_one_initcall+0x100/0x1b8)
[    8.988983] [<c00097e0>] (do_one_initcall) from [<c00b8008>] (do_init_module+0x58/0x1c0)
[    8.997497] [<c00b8008>] (do_init_module) from [<c00b8cac>] (SyS_init_module+0x54/0x64)
[    9.005950] [<c00b8cac>] (SyS_init_module) from [<c000ed20>] (ret_fast_syscall+0x0/0x54)
[    9.015838] input: twl4030:vibrator as /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:audio/input/input2

node passed to of_find_node_by_name is put inside that function and new node
is returned if found. Free returned node not already freed node.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It turns out that only Dell laptops have the separate button bits for
v2 dualpoint sticks and that commit 92bac83d ("Input: alps - non
interleaved V2 dualpoint has separate stick button bits") causes
regressions on Toshiba laptops.

This commit adds a check for Dell laptops to the code for handling these
extra button bits, fixing this regression.

This patch has been tested on a Dell Latitude D620 to make sure that it
does not reintroduce the original problem.

Reported-and-tested-by: Douglas Christman <douglaschristman@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add a proper module alias so the driver can be autoloaded when the
parent axp20x mfd driver registers its cells.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Patch 17dd3f0f: "[PATCH] drivers/input/joystick: convert to dynamic
input_dev allocation" from Sep 15, 2005, leads to the following static
checker warning:

        drivers/input/joystick/turbografx.c:235 tgfx_probe()
        error: buffer overflow 'tgfx_buttons' 5 <= 5

drivers/input/joystick/turbografx.c
   195          for (i = 0; i < n_devs; i++) {
   196                  if (n_buttons[i] < 1)
   197                          continue;
   198
   199                  if (n_buttons[i] > 6) {
                            ^^^^^^^^^^^^^^^^
Possibly off by one.  >= 6.

Let's change the upper value to ARRAY_SIZE(tgfx_buttons) to ensure we do
not reach past the end of the array.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 7d01cd26 because
with given FRAME_MAXSIZE of 257 the check will never trigger and it
causes warnings from GCC (with -Wtype-limits). Also the check was
incorrect as it was not accounting for the already read 2 bytes of data
stored in the buffer.

Add support for the MacBookPro12,1 model. This patch needs to be
applied together with the accompanied HID patch, as usual.

Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds keyboard support for MacbookPro12,1 as WELLSPRING9
(0x0272, 0x0273, 0x0274). The touchpad is handled in a separate
bcm5974 patch, as usual.

Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

With the advent of the Macbook Pro 12, we see a new generation of
trackpads, capable of force sensoring and haptic feedback.

This patch prepares for the new device by adding configuration data
for the code paths that would otherwise look different.

Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make extended capabilities obtained through $10 query also available in
touchpad identification.

Signed-off-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.

  1280,800             0,800
         +-------------+
         |             |
         |             |
         |             |
         +-------------+
    1280,0             0,0

It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.

Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.

Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen.  Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.

According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.

The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.

Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

All Elantech touchpads pre-v4 with dynamic resolution queries have a fixed
resolution of 800dpi -> 31.49 units/mm. Set this statically, so userspace
does not have to guess.

Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If we get a corrupted packet with PAYLOAD_LENGTH > FRAME_MAXSIZE, we
will silently overwrite the stack.

Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <external.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 63c4fda3 as it
causes issues with detecting 3-finger taps.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100481


Cc: stable@vger.kernel.org
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>

The firmware only reports hover condition while the very first contact is
approaching the surface; the hover is not reported for the subsequent
contacts. Therefore we should not be using ABS_MT_DISTANCE to report hover
but rather its single-touch counterpart ABS_DISTANCE.

Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare second round of input updates for 4.2 merge window.

Get the scaling factor when it reads the sys params. The width value will
multiple the factor and report the value in the TOUCH_MAJOR event.

Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There is no reason to have a newline between plat_id and xml_id1.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix this compile error:

drivers/built-in.o: In function `arc_ps2_probe':
/mnt/linux/drivers/input/serio/arc_ps2.c:206: undefined reference to `devm_ioremap_resource'

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This fixes the following warning:

   drivers/input/touchscreen/wdt87xx_i2c.c: In function 'wdt87xx_validate_firmware':
>> drivers/input/touchscreen/wdt87xx_i2c.c:472:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'size_t' [-Wformat=]
       size, fw->size);

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When applying touchscreen parameters specified in device tree let's make
sure we keep whatever setup was done by the driver and not reset the
missing values to zero.

Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

edt-ft5x06 is a touchscreen and thus a direct input device; let's amrk it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of iterating over all bits in a bitmap and test them individually
let's siwtch to for_each_set_bit() which is more compact and is also
faster.

Also use bitmap_weight() when counting number of set bits.

This also fixes INPUT_DO_TOGGLE() implementation as it should have used
*_CNT as the upper boundary, not *_MAX.

Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This is a driver for Weida HiTech WDT87xx series touchscreen controller.

Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Currently we are reporting the button state as inverted on all boards with
an axp209 pmic, tested on a ba10-tvbox, bananapi, bananapro, cubietruck and
utoo-p66 tablet.

The axp209 datasheet clearly states that the power button must be connected
between the PWRON key and ground. Which means that on a press we will get
a falling edge (dbf) irq not a rising one, and likewise on release we will
get a rising edge (dbr) irq, not a falling one.

This commit swaps the check for the 2 irqs fixing the inverted reporting of
the power button state.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.

Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Based on Patch by Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>:
Add the logic to set the LEDs on XBox Wireless controllers.  Command
sequence found by sniffing the Windows data stream when plugging the
device in.

Updated based on comments on linux-input:
unify codepaths in xpad_send_led_command for wired/ wireless controller.
Also document command values for clarification.
All values tested on Xbox 360 Wireless Controller.

Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare first round of input updates for 4.2 merge window.

The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.

Fixes: 36874c7e ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)

Cc: stable@vger.kernel.org
Signed-off-by: Frodo Lai <frodo_lai@bcmcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The "INPUT MULTITOUCH (MT) PROTOCOL" entry git tree is not there on
git.kernel.org.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.

Note that in the case of the drv260x driver error checking is more
strict now because -ENOSYS is reported to the caller now. But this
should only be returned if GPIOLIB is disabled which shouldn't happen as
the driver depends on GPIOLIB.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In addition to defining triggers for VT LED states, let's define triggers
for VT keyboard lock states, such as "kbd-shiftlock", "kbd-altgrlock", etc.

This permits to fix #7063 from userland by using a modifier to implement
proper CapsLock behavior and have the keyboard caps lock led show that
modifier state.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Now that input core allows controlling keyboards LEDs via standard LED
subsystem triggers let's switch VT keyboard code to make use of this
feature. We will define the following standard triggers: "kbd-scrollock",
"kbd-numlock", "kbd-capslock", and "kbd-kanalock" which are default
triggers for respective LEDs on keyboards.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).

The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use kernel.h macro definition.

Thanks to Julia Lawall for Coccinelle scripting support.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>