Add driver for Cadence SPI controller. This is used in Xilinx Zynq.

Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

The tnetv107x platform is getting removed, so this driver
will not be needed any more.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

This simple SPI master controller is built into xtfpga bitstreams. It
always transfers 16 bit words in SPI mode 0, automatically asserting CS
on transfer start and deasserting on end.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.

Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.

Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Qualcomm Universal Peripheral (QUP) core is an AHB slave that
provides a common data path (an output FIFO and an input FIFO)
for serial peripheral interface (SPI) mini-core. SPI in master
mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.

Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: dsneddon@codeaurora.org
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.

It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs.

It does feature some new modes like 3-wire or dual spi, but neither of it
is currently implemented.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

The patch add basic support for the quad spi controller.

QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.

The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).

Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
   - All iterations went through without failure.
Test2: Use mtd utilities:
  - flash_erase to erase the flash device
  - mtd_debug read to read data back.
  - mtd_debug write to write to the data flash.
 diff between the write and read data shows zero.

Acked-by: Felipe <Balbi&lt;balbi@ti.com>
Reviewed-by: Felipe <Balbi&lt;balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

The serial peripheral interface (SPI) module implemented on Freescale Vybrid
platform provides a synchronous serial bus for communication between Vybrid
and the external peripheral device.
The SPI supports full-duplex, three-wire synchronous transfer, has TX/RX FIFO
with depth of four entries.

This driver is the SPI master mode driver and has been tested on Vybrid
VF610TWR board.

Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>

New spi controller(version 3) is integrated into Blackfin
60x processor. Comparing to bf5xx spi controller, we support
32 bits word size and independent receive and transmit DMA
channels now. Also mode 0 and 2 (CPHA = 0) can get fully
supported becasue cs line may be controlled by the software.

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Add SPI driver for NVIDIA's Tegra114 SPI controller. This controller
is different than the older SoCs SPI controller in internal design as
well as register interface.

This driver supports the:
- non DMA based transfer for smaller transfer i.e. less than FIFO depth.
- APB DMA based transfer for larger transfer i.e. more than FIFO depth.
- Clock gating through runtime PM callbacks.
- registration through DT only.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This makes the spi-fsl-spi driver usable in CPU mode outside of an FSL_SOC and
even an powerpc environment by moving CPM mode functionality to a separate file
that is only compiled and linked in an FSL_SOC environment and adding some
ifdefs to hide types and functions or provide alternatives.

For devicetree probing a "clock-frequency" property is used for clock frequency
instead of calls to FSL_SOC-specific functions.

Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The BCM2835 contains two forms of SPI master controller (one known
simply as SPI0, and the other known as the "Universal SPI Master", in
the auxilliary block) and one form of SPI slave controller. This patch
adds support for the SPI0 controller.

This driver is taken from Chris Boot's repository at
git://github.com/bootc/linux.git rpi-linear
as of commit 6de2905 "spi-bcm2708: fix printf with spurious %s".
In the first SPI-related commit there, Chris wrote:

Thanks to csoutreach / A Robinson for his driver which I used as an
inspiration. You can find his version here:
http://piface.openlx.org.uk/raspberry-pi-spi-kernel-driver-available-for



Changes made during upstreaming:
* Renamed bcm2708 to bcm2835 as per upstream naming for this SoC.
* Removed support for brcm,realtime property.
* Increased transfer timeout to 30 seconds.
* Return IRQ_NONE from the IRQ handler if no interrupt was handled.
* Disable TA (Transfer Active) and clear FIFOs on a transfer timeout.
* Wrote device tree binding documentation.
* Request unnamed clock rather than "sys_pclk"; the DT will provide the
  correct clock.
* Assume that tfr->speed_hz and tfr->bits_per_word are always set in
  bcm2835_spi_start_transfer(), bcm2835_spi_transfer_one(), so no need
  to check spi->speed_hz or tft->bits_per_word.
* Re-ordered probe() to remove the need for temporary variables.
* Call clk_disable_unprepare() rather than just clk_unprepare() on probe()
  failure.
* Don't use devm_request_irq(), to ensure that the IRQ doesn't fire after
  we've torn down the device, but not unhooked the IRQ.
* Moved probe()'s call to clk_prepare_enable() so we can be sure the clock
  is enabled if the IRQ handler fires immediately.
* Remove redundant checks from bcm2835_spi_check_transfer() and
  bcm2835_spi_setup().
* Re-ordered IRQ handler to check for RXR before DONE. Added comments to
  ISR.
* Removed empty prepare/unprepare implementations.
* Removed use of devinit/devexit.
* Added BCM2835_ prefix to defines.

Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.

Request lines and channel numbers can be passed to the driver from the
platform specific data.

The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).

While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.

Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This driver is obsolete and can't even be built anymore since the
platform it depends has been removed.

The STMP series is completely covered by the MXS platform these days, so
spi-mxs can be used instead.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch add new driver for CLPS711X SPI master controller.
Due to platform limitations driver supports only 8 bit transfer mode.
Chip select control is handled via GPIO.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

NVIDIA's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add the spi driver for this controller.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The current SPI driver has many issues. Examples are:

* Segfaulting on most transfers due to expecting all transfers to have
  both RX and TX buffers.
* Hanging on TX transfers since the whole driver flow is driven by RX
  DMA completion, but the HW is only told to enable RX for RX transfers.
* Use of clk_disable_unprepare() from atomic context.
* Once those and other minor issues are fixed, the driver still doesn't
  actually work.
* The driver also implements a deprecated API to the SPI core.

For this reason, simply remove the driver completely. This has two
advantages:

1) This will remove the last use of Tegra's <mach/dma.h>, which will
   allow that file to be removed, which is required for single zImage
   work.

2) The downstream driver is significaly different from the current
   code. I believe a patch to re-add the downstream driver (with
   appropriate cleanup) will be much simpler to review if it's a new
   file rather than randomly interspered with essentially unrelated
   existing code.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add the driver, link it into the kbuild system and provide device tree
binding documentation.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/4292/


Signed-off-by: John Crispin <blogic@openwrt.org>

This driver adds support for NXP SC18IS602/603 I2C to SPI bus bridge.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is slightly reworked version of the SPI driver.
Support for DT has been added and it's been converted
to queued API.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The external bus unit (EBU) found on the FALCON SoC has spi emulation that is
designed for serial flash access. This driver has only been tested with m25p80
type chips. The hardware has no support for other types of spi peripherals.

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: spi-devel-general@lists.sourceforge.net
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3844/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds support for the I2C-SPI bridge which can be found on the Analog
Devices AD-FMCOMMS1-EBZ board.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This controller is only for blackfin 5xx soc, so rename it to BFIN5XX

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch adds support for the SPI controller found on the Broadcom BCM63xx
SoCs.

Signed-off-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

CSR SiRFprimaII has two SPIs (SPI0 and SPI1). Features:
* Master and slave modes
* 8-/12-/16-/32-bit data unit
* 256 bytes receive data FIFO and 256 bytes transmit data FIFO
* Multi-unit frame
* Configurable SPI_EN (chip select pin) active state
* Configurable SPI_CLK polarity
* Configurable SPI_CLK phase
* Configurable MSB/LSB first

Signed-off-by: Zhiwu Song <zhiwu.song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The SH7757 has RSPI module. This patch supports it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

It was equivalent to spi-gpio, and there's no longer any in-tree users
of it, so get rid of it.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.

This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.

v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
      be the predominant pattern for subsystem prefixes.
    - Clean up filenames in Kconfig and header comment blocks

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

The Blackfin SPORT peripheral is a pretty flexible device.  With enough
coaching, we can make it generate SPI compatible waveforms.  This is
desirable as the SPORT can run at much higher clock frequencies than the
dedicated on-chip SPI peripheral, and it can do full duplex DMA.  It also
opens up the possibility of multiple SPI buses in case someone wants to
dedicate a whole bus to a specific part that does not play well with
others.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.

Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The SH7757 has SPI0 module. This patch supports it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[grant.likely@secretlab.ca: fixed Makefile ordering, added
    __dev{init,exit} annotations, removed DRIVER_VERSION (this is
    mainline, the version == the kernel version) and tidied some
    indentation & style stuff]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch adds a new SPI driver to support the Altera SOPC Builder
SPI component. It uses the bitbanging library.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This patch adds support of OpenCores tiny SPI driver.

http://opencores.org/project,tiny_spi



Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms

It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled

Also change the dma interface suggested by Linus Walleij.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>