ieee80211_start_roc_work() might add a new roc
to existing roc, and tell cfg80211 it has already
started.

However, this might happen before the roc cookie
was set, resulting in REMAIN_ON_CHANNEL (started)
event with null cookie. Consequently, it can make
wpa_supplicant go out of sync.

Fix it by setting the roc cookie earlier.

Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This patch fixed following Warning while executing "make htmldocs".

Warning(/net/core/skbuff.c:2164): No description found for parameter 'from'
Warning(/net/core/skbuff.c:2164): Excess function parameter 'source'
description in 'skb_zerocopy'
Replace "@source" with "@from" fixed the warning.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sending malformed llc packets triggers this spew, which seems excessive.

WARNING: CPU: 1 PID: 6917 at net/llc/llc_output.c:46 llc_mac_hdr_init+0x85/0x90 [llc]()
device type not supported: 0
CPU: 1 PID: 6917 Comm: trinity-c1 Not tainted 3.13.0+ #95
 0000000000000009 00000000007e257d ffff88009232fbe8 ffffffffac737325
 ffff88009232fc30 ffff88009232fc20 ffffffffac06d28d ffff88020e07f180
 ffff88009232fec0 00000000000000c8 0000000000000000 ffff88009232fe70
Call Trace:
 [<ffffffffac737325>] dump_stack+0x4e/0x7a
 [<ffffffffac06d28d>] warn_slowpath_common+0x7d/0xa0
 [<ffffffffac06d30c>] warn_slowpath_fmt+0x5c/0x80
 [<ffffffffc01736d5>] llc_mac_hdr_init+0x85/0x90 [llc]
 [<ffffffffc0173759>] llc_build_and_send_ui_pkt+0x79/0x90 [llc]
 [<ffffffffc057cdba>] llc_ui_sendmsg+0x23a/0x400 [llc2]
 [<ffffffffac605d8c>] sock_sendmsg+0x9c/0xe0
 [<ffffffffac185a37>] ? might_fault+0x47/0x50
 [<ffffffffac606321>] SYSC_sendto+0x121/0x1c0
 [<ffffffffac011847>] ? syscall_trace_enter+0x207/0x270
 [<ffffffffac6071ce>] SyS_sendto+0xe/0x10
 [<ffffffffac74aaa4>] tracesys+0xdd/0xe2

Until 2009, this was a printk, when it was changed in
bf9ae538: "llc: use dev_hard_header".

Let userland figure out what -EINVAL means by itself.

Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dealing with icmp messages, the skb->data points the
ip header that triggered the sending of the icmp message.

In gre_cisco_err(), the parse_gre_header() is called, and the
iptunnel_pull_header() is called to pull the skb at the end of
the parse_gre_header(), so the skb->data doesn't point the
inner ip header.

Unfortunately, the ipgre_err still needs those ip addresses in
inner ip header to look up tunnel by ip_tunnel_lookup().

So just use icmp_hdr() to get inner ip header instead of skb->data.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

I see a memory leak when using a transparent HTTP proxy using TPROXY
together with TCP early demux and Kernel v3.8.13.15 (Ubuntu stable):

unreferenced object 0xffff88008cba4a40 (size 1696):
  comm "softirq", pid 0, jiffies 4294944115 (age 8907.520s)
  hex dump (first 32 bytes):
    0a e0 20 6a 40 04 1b 37 92 be 32 e2 e8 b4 00 00  .. j@..7..2.....
    02 00 07 01 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff810b710a>] kmem_cache_alloc+0xad/0xb9
    [<ffffffff81270185>] sk_prot_alloc+0x29/0xc5
    [<ffffffff812702cf>] sk_clone_lock+0x14/0x283
    [<ffffffff812aaf3a>] inet_csk_clone_lock+0xf/0x7b
    [<ffffffff8129a893>] netlink_broadcast+0x14/0x16
    [<ffffffff812c1573>] tcp_create_openreq_child+0x1b/0x4c3
    [<ffffffff812c033e>] tcp_v4_syn_recv_sock+0x38/0x25d
    [<ffffffff812c13e4>] tcp_check_req+0x25c/0x3d0
    [<ffffffff812bf87a>] tcp_v4_do_rcv+0x287/0x40e
    [<ffffffff812a08a7>] ip_route_input_noref+0x843/0xa55
    [<ffffffff812bfeca>] tcp_v4_rcv+0x4c9/0x725
    [<ffffffff812a26f4>] ip_local_deliver_finish+0xe9/0x154
    [<ffffffff8127a927>] __netif_receive_skb+0x4b2/0x514
    [<ffffffff8127aa77>] process_backlog+0xee/0x1c5
    [<ffffffff8127c949>] net_rx_action+0xa7/0x200
    [<ffffffff81209d86>] add_interrupt_randomness+0x39/0x157

But there are many more, resulting in the machine going OOM after some
days.

From looking at the TPROXY code, and with help from Florian, I see
that the memory leak is introduced in tcp_v4_early_demux():

  void tcp_v4_early_demux(struct sk_buff *skb)
  {
    /* ... */

    iph = ip_hdr(skb);
    th = tcp_hdr(skb);

    if (th->doff < sizeof(struct tcphdr) / 4)
        return;

    sk = __inet_lookup_established(dev_net(skb->dev), &tcp_hashinfo,
                       iph->saddr, th->source,
                       iph->daddr, ntohs(th->dest),
                       skb->skb_iif);
    if (sk) {
        skb->sk = sk;

where the socket is assigned unconditionally to skb->sk, also bumping
the refcnt on it.  This is problematic, because in our case the skb
has already a socket assigned in the TPROXY target.  This then results
in the leak I see.

The very same issue seems to be with IPv6, but haven't tested.

Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow redirect replies from osds, for details see ceph.git commit
fbbe3ad1220799b7bb00ea30fce581c5eadaf034.

v1 (current) version of redirect reply consists of oloc and oid, which
expands to pool, key, nspace, hash and oid.  However, server-side code
that would populate anything other than pool doesn't exist yet, and
hence this commit adds support for pool redirects only.  To make sure
that future server-side updates don't break us, we decode all fields
and, if any of key, nspace, hash or oid have a non-default value, error
out with "corrupt osd_op_reply ..." message.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

Rename ceph_osd_request::r_{oloc,oid} to r_base_{oloc,oid} before
introducing r_target_{oloc,oid} needed for redirects.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

Overwrite ceph_osd_request::r_oloc.pool with read_tier for read ops and
write_tier for write and read+write ops (aka basic tiering support).
{read,write}_tier are part of pg_pool_t since v9.  This commit bumps
our pg_pool_t decode compat version from v7 to v9, all new fields
except for {read,write}_tier are ignored.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

"Lookup pool info by ID" function is hidden in osdmap.c.  Expose it to
the rest of libceph.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

Switch ceph_calc_ceph_pg() to new oloc and oid abstractions and rename
it to ceph_oloc_oid_to_pg() to make its purpose more clear.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

In preparation for tiering support, which would require having two
(base and target) object names for each osd request and also copying
those names around, introduce struct ceph_object_id (oid) and a couple
helpers to facilitate those copies and encapsulate the fact that object
name is not necessarily a NUL-terminated string.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

In preparation for adding oid abstraction, rename MAX_OBJ_NAME_SIZE to
CEPH_MAX_OID_NAME_LEN.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

Instead of relying on pool fields in ceph_file_layout (for mapping) and
ceph_pg (for enconding), start using ceph_object_locator (oloc)
abstraction.  Note that userspace oloc currently consists of pool, key,
nspace and hash fields, while this one contains only a pool.  This is
OK, because at this point we only send (i.e. encode) olocs and never
have to receive (i.e. decode) them.

This makes keeping a copy of ceph_file_layout in every osd request
unnecessary, so ceph_osd_request::r_file_layout field is nuked.

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

PTR_RET is deprecated. Use PTR_ERR_OR_ZERO instead. While at it
also include missing err.h header.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.

Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On input, CHECKSUM_PARTIAL should be treated the same way as
CHECKSUM_UNNECESSARY. See include/linux/skbuff.h

Signed-off-by: Tim Smith <tim@electronghost.co.uk>
Signed-off-by: David Howells <dhowells@redhat.com>

skb_kill_datagram() does not dequeue the skb when MSG_PEEK is unset.
This leaves a free'd skb on the queue, resulting a double-free later.

Without this, the following oops can occur:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8154fcf7>] skb_dequeue+0x47/0x70
PGD 0
Oops: 0002 [#1] SMP
Modules linked in: af_rxrpc ...
CPU: 0 PID: 1191 Comm: listen Not tainted 3.12.0+ #4
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: ffff8801183536b0 ti: ffff880035c92000 task.ti: ffff880035c92000
RIP: 0010:[<ffffffff8154fcf7>] skb_dequeue+0x47/0x70
RSP: 0018:ffff880035c93db8  EFLAGS: 00010097
RAX: 0000000000000246 RBX: ffff8800d2754b00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000202 RDI: ffff8800d254c084
RBP: ffff880035c93dd0 R08: ffff880035c93cf0 R09: ffff8800d968f270
R10: 0000000000000000 R11: 0000000000000293 R12: ffff8800d254c070
R13: ffff8800d254c084 R14: ffff8800cd861240 R15: ffff880119b39720
FS:  00007f37a969d740(0000) GS:ffff88011fc00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 00000000d4413000 CR4: 00000000000006f0
Stack:
 ffff8800d254c000 ffff8800d254c070 ffff8800d254c2c0 ffff880035c93df8
 ffffffffa041a5b8 ffff8800cd844c80 ffffffffa04385a0 ffff8800cd844cb0
 ffff880035c93e18 ffffffff81546cef ffff8800d45fea00 0000000000000008
Call Trace:
 [<ffffffffa041a5b8>] rxrpc_release+0x128/0x2e0 [af_rxrpc]
 [<ffffffff81546cef>] sock_release+0x1f/0x80
 [<ffffffff81546d62>] sock_close+0x12/0x20
 [<ffffffff811aaba1>] __fput+0xe1/0x230
 [<ffffffff811aad3e>] ____fput+0xe/0x10
 [<ffffffff810862cc>] task_work_run+0xbc/0xe0
 [<ffffffff8106a3be>] do_exit+0x2be/0xa10
 [<ffffffff8116dc47>] ? do_munmap+0x297/0x3b0
 [<ffffffff8106ab8f>] do_group_exit+0x3f/0xa0
 [<ffffffff8106ac04>] SyS_exit_group+0x14/0x20
 [<ffffffff8166b069>] system_call_fastpath+0x16/0x1b


Signed-off-by: Tim Smith <tim@electronghost.co.uk>
Signed-off-by: David Howells <dhowells@redhat.com>

If rx->conn is not NULL, rxrpc_connect_exclusive() does not
acquire the transport's client lock, but it still releases it.

The patch adds locking of the spinlock to this path.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David Howells <dhowells@redhat.com>

Add a missing newline to a dout() in __reset_osd().

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>

Encapsulate kmalloc vs vmalloc memory allocation and freeing logic into
two helpers, ceph_kvmalloc() and ceph_kvfree(), and switch to them.

ceph_kvmalloc() kmalloc()'s a maximum of 8 pages, anything bigger is
vmalloc()'ed with __GFP_HIGHMEM set.  This changes the existing
behaviour:

- for buffers (ceph_buffer_new()), from trying to kmalloc() everything
  and using vmalloc() just as a fallback

- for messages (ceph_msg_new()), from going to vmalloc() for anything
  bigger than a page

- for messages (ceph_msg_new()), from disallowing vmalloc() to use high
  memory

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>

commit 25fb6ca4
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
allocates addrconf router for ipv6 address when lo device up.
but commit a881ae1f
"ipv6:don't call addrconf_dst_alloc again when enable lo" breaks
this behavior.

Since the addrconf router is moved to the garbage list when
lo device down, we should release this router and rellocate
a new one for ipv6 address when lo device up.

This patch solves bug 67951 on bugzilla
https://bugzilla.kernel.org/show_bug.cgi?id=67951



change from v1:
use ip6_rt_put to repleace ip6_del_rt, thanks Hannes!
change code style, suggested by Sergei.

CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two commits 0115e8e3 (net: remove delay at device dismantle) and
748e2d93 (net: reinstate rtnl in call_netdevice_notifiers()) silently
removed a NULL pointer check for in_dev since Linux 3.7.

This patch re-introduces this check as it causes crashing the kernel when
setting small mtu values on non-ip capable netdevices.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace hardcoded lowest common multiple algorithm by the lcm()
function in kernel lib.

Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

Use rbtree_postorder_for_each_entry_safe() to destroy the rbtree instead
of opencoding an alternate postorder iteration that modifies the tree

Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Now that the definition is centralized in <linux/kernel.h>, the
definitions of U32_MAX (and related) elsewhere in the kernel can be
removed.

Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Sage Weil <sage@inktank.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The symbol U32_MAX is defined in several spots.  Change these
definitions to be conditional.  This is in preparation for the next
patch, which centralizes the definition in <linux/kernel.h>.

Signed-off-by: Alex Elder <elder@linaro.org>
Cc: Sage Weil <sage@inktank.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This check is not needed because the same check is done before
fill_slave_info is used in rtnl_link_slave_info_fill.
Also, by removing this check, kernel will fillup IFLA_INFO_SLAVE_KIND
even for slaves of masters which does not implement fill_slave_info.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit a6222602("ip_tunnel: fix kernel panic with icmp_dest_unreach")
clear IPCB in ip_tunnel_xmit()  , or else skb->cb[] may contain garbage from
GSO segmentation layer.

But commit 0e6fbc5b("ip_tunnels: extend iptunnel_xmit()") refactor codes,
and it clear IPCB behind the dst_link_failure().

So clear IPCB in ip_tunnel_xmit() just like commti a6222602("ip_tunnel:
fix kernel panic with icmp_dest_unreach").

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we have multiple devices attempting to sync the same address
to a single destination, each device should be permitted to sync
it once.  To accomplish this, pass the 'sync_cnt' of the source
address when adding the addresss to the lower device.  'sync_cnt'
tracks how many time a given address has been succefully synced.
This way, we know that if the 'sync_cnt' passed in is 0, we should
sync this address.

Also, turn 'synced' member back into the counter as was originally
done in
   commit 4543fbef.
   net: count hw_addr syncs so that unsync works properly.
It tracks how many time a given address has been added via a
'sync' operation.  For every successfull 'sync' the counter is
incremented, and for ever 'unsync', the counter is decremented.
This makes sure that the address will be properly removed from
the the lower device when all the upper devices have removed it.

Reported-by: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru>
CC: Konstantin Ushakov <Konstantin.Ushakov@oktetlabs.ru>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed few issues around using __rcu prefix and rcu_assign_pointer, also
fixed a warning print to use ntohs(port) and not htons(port).

net/ipv4/udp_offload.c:112:9: error: incompatible types in comparison expression (different address spaces)
net/ipv4/udp_offload.c:113:9: error: incompatible types in comparison expression (different address spaces)
net/ipv4/udp_offload.c:176:19: error: incompatible types in comparison expression (different address spaces)

Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A socket may be v6/v4-mapped. In that case sk->sk_family is AF_INET6,
but the IP being used is actually an IPv4-address.
Current's tcp-metrics will thus represent it as an IPv6-address:

root@server:~# ip tcp_metrics
::ffff:10.1.1.2 age 22.920sec rtt 18750us rttvar 15000us cwnd 10
10.1.1.2 age 47.970sec rtt 16250us rttvar 10000us cwnd 10

This patch modifies the tcp-metrics so that they are able to handle the
v6/v4-mapped sockets correctly.

Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 8df8c56a, 6lowpan_iphc is a module of its own.

Unfortunately, it lacks some infrastructure to behave like a
good kernel citizen:

  kernel: 6lowpan_iphc: module license 'unspecified' taints kernel.
  kernel: Disabling lock debugging due to kernel taint

This patch adds the basic MODULE_LICENSE(); with GPL license:
the code was copied from net/ieee802154/6lowpan.c which is GPL
and the module exports symbol with EXPORT_SYMBOL_GPL();.

Cc: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88a)

Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.

This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Workqueue used in neighbour layer have no real dependency of scheduling these on
the cpu which scheduled them.

On a idle system, it is observed that an idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.

This patch replaces normal workqueues with power efficient versions. This
doesn't change existing behavior of code unless CONFIG_WQ_POWER_EFFICIENT is
enabled.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Workqueue used in ipv4 layer have no real dependency of scheduling these on the
cpu which scheduled them.

On a idle system, it is observed that an idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.

This patch replaces normal workqueues with power efficient versions. This
doesn't change existing behavior of code unless CONFIG_WQ_POWER_EFFICIENT is
enabled.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change allows to consider an anycast address valid as source address
when given via an IPV6_PKTINFO or IPV6_2292PKTINFO ancillary data item.
So, when sending a datagram with ancillary data, the unicast and anycast
addresses are handled in the same way.

- Adds ipv6_chk_acast_addr_src() to check if an anycast address is link-local
  on given interface or is global.
- Uses it in ip6_datagram_send_ctl().

Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

br_handle_vlan() pushes HW accelerated vlan tag into skbuff when outgoing
port is the bridge device.
This is unnecessary because __netif_receive_skb_core() can handle skbs
with HW accelerated vlan tag. In current implementation,
__netif_receive_skb_core() needs to extract the vlan tag embedded in skb
data. This could cause low network performance especially when receiving
frames at a high frame rate on the bridge device.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>