Integrate u-boot-seco-imx/seco_lf_v2024.04_6.6.52_2.2.x-tr8mp-dev (!636) · Merge requests · Clea OS / layers / seco / meta-seco-imx

Git Bot Service Account requested to merge u-boot-seco-imx/seco_lf_v2024.04_6.6.52_2.2.x-tr8mp-dev into scarthgap Sep 16, 2025

Commit: clea-os/bsp/nxp/u-boot-seco-imx@a188ba30

[DTS][TRIZEPS8PLUS] Enable USB power

Enables the regulator for USB-OTG, USB-HOST, and asserts the RESET_OUT#. RESET_OUT# is needed for USB Hub on pConXS and might be useful for other periperals

Commit: clea-os/bsp/nxp/u-boot-seco-imx@06e486f8

[BOARD][TRIZEPS8PLUS] Adjust cma size based on RAM size

Copied from D18

Commit: clea-os/bsp/nxp/u-boot-seco-imx@a2de06ca

[ENV][TRIZEPS8PLUS] Add peripheral option for BT over UART3

Commit: clea-os/bsp/nxp/u-boot-seco-imx@d13fc9b0

[ENV][TRIZEPS8PLUS] Add PCIe overlay options

Commit: clea-os/bsp/nxp/u-boot-seco-imx@6f4f46b7

[ENV][TRIZEPS8PLUS] Configure slower LDB_CLK

Commit: clea-os/bsp/nxp/u-boot-seco-imx@668c1873

[DTS][TRIZEPS8PLUS] Remove assigned clock properties from lcdif2 and ldb nodes

Commit: clea-os/bsp/nxp/u-boot-seco-imx@3ad6818f

[BOARD][TRIZEPS8PLUS] Enable pwm in board file

The regulator driver isn't enabling the pwm when defined in the device tree, thus doing it from the machine file

Commit: clea-os/bsp/nxp/u-boot-seco-imx@e0652013

[CONFIG][TRIZEPS8PLUS] Enable LVDS and splashscreen

Commit: clea-os/bsp/nxp/u-boot-seco-imx@43e04524

[DTS][TRIZEPS8PLUS] Add LVDS single-channel video support

On pConXS III and i-PAN T7 II: panel AZ ATM0700L61CT

Commit: clea-os/bsp/nxp/u-boot-seco-imx@81da0e1a

[ENV][TRIZEPS8PLUS] Add i-PAN T7 II carrier board option

Commit: clea-os/bsp/nxp/u-boot-seco-imx@4c3f6cc1

[ENV][TRIZEPS8PLUS] Add video overlay option HDMI + LVDS

Commit: clea-os/bsp/nxp/u-boot-seco-imx@ac6b7a45

[BOARD][TRIZEPS8PLUS] Manage custom overlays for peripherals

Commit: clea-os/bsp/nxp/u-boot-seco-imx@058c1d69

[CONFIG][TRIZEPS8PLUS] Enable eeprom manager and seco_fdt_overlay

Commit: clea-os/bsp/nxp/u-boot-seco-imx@bba50065

[DT][TRIZEPS8PLUS] Switch serial output to UART1

Commit: clea-os/bsp/nxp/u-boot-seco-imx@347deac1

[BOARD][TRIZEPS8PLUS] Switch serial output to UART1

Commit: clea-os/bsp/nxp/u-boot-seco-imx@2686f8a7

[ENV][TRIZEPS8PLUS] Switch serial output to UART1

Commit: clea-os/bsp/nxp/u-boot-seco-imx@69faaf1f

[DT][TRIZEPS8PLUS] Add support for ethernet phy

Commit: clea-os/bsp/nxp/u-boot-seco-imx@705b8815

[ENV][TRIZEPS8PLUS] Conditionally show RGB video option

only when FPGA is detected

Commit: clea-os/bsp/nxp/u-boot-seco-imx@68d99d12

[BOARD][TRIZEPS8PLUS] Add peripherals autodetection

Starting with V1R5, there is an option to control the WiFi module without MCU. Will need to apply an overlay based on revision and presence of MCU. Also added FPGA detection for FPGA-specific seco_config entries.

Commit: clea-os/bsp/nxp/u-boot-seco-imx@eeab62e5

[SPL][TRIZEPS8PLUS] Enable LDO4

FPGA is supplied with this power rail, we need it enabled for FPGA probing during autodetection

Commit: clea-os/bsp/nxp/u-boot-seco-imx@fb860fba

[DT][TRIZEPS8PLUS] Adjust I2C busses

remove non-existing i2c5
move pmic to i2c3

Commit: clea-os/bsp/nxp/u-boot-seco-imx@2c55765a

[DT][TRIZEPS8PLUS] Refine SD1 and SD2 configurations

Removed gpio1_3 pin from PMIC interrupt. It is used for IO voltage switch for SD1
SD1 now supports the internal SD card with voltage switching (option instead of eMMC)
SD2 Added vmmc regulator for completeness

Commit: clea-os/bsp/nxp/u-boot-seco-imx@5bf40fb5

[ENV][TRIZEPS8PLUS] Add peripheral overlay options: CSI0

Commit: clea-os/bsp/nxp/u-boot-seco-imx@9784dc1a

[ENV][TRIZEPS8PLUS] Add video overlay options

Commit: clea-os/bsp/nxp/u-boot-seco-imx@0083af56

[ENV][TRIZEPS8PLUS] Add carrier overlay options

Commit: clea-os/bsp/nxp/u-boot-seco-imx@9f645804

[TRIZEPS8PLUS] Add dynamic RAM size support

Commit: clea-os/bsp/nxp/u-boot-seco-imx@2d83990e

[TRIZEPS8PLUS] Remove DDR4 timings

We only have LPDDR4 options

Commit: clea-os/bsp/nxp/u-boot-seco-imx@5de9ab99