Teresa Remmet authored 4 years ago and Gianfranco Mariotti committed 5 months ago

As clk_get_rate() also keeps the clk prepare lock which can lead into a
deadlock. It was removed upstream with this commit:
(90ad2cbe) i2c: imx: use clk notifier for rate changes

But it has been readded again with:
(d2561688) MLK-20368 i2c-imx: Coverity: fix divide by zero warning

The commit message does not explain why it was readded. It is not needed
as the clk notifier is used. Removed it again.

REFERENCE: https://github.com/nxp-imx/linux-imx/pull/21

Workaround for NXP chip errata ERR007805 "I2C: When the I2C clock speed is
configured for 400 kHz, the SCL low period violates the I2C spec of 1.3 uS min"
This errata is found on the following SoCs:
* MX8M{M,N,P,Q}
* MX7{S,D}
* MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP}

Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.

REFERENCE: https://lore.kernel.org/linux-arm-kernel/YlngkTlsJ8M1gB3z@shikoro/T/

[ Upstream commit 47ff6172 ]

In i2c_imx_xfer() and i2c_imx_remove(), the pm reference count
is not expected to be incremented on return.

However, pm_runtime_get_sync will increment pm reference count
even failed. Forgetting to putting operation will result in a
reference leak here.

Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.

Fixes: 3a5ee18d ("i2c: imx: implement master_xfer_atomic callback")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

If add this arbitration check, it will block camera probe on imx7D-sdb.
So remove this check for now to avoid blocking camera function in TC
release.

Repreduce step:
1. Write 0x42 to 0x3008 reg
2. Write 0x2 to 0x3008 reg
Then the arbitration lost flag will be set.

Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>

Add the missing pm_runtime_disable() to keep the balance of
power.disable_depth in i2c_imx_xfer function.
Otherwise, after resumed, warning log will be shown:

imx-i2c 30a20000.i2c: Unbalanced pm_runtime_enable!

Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>

Auto switch mode between master and slave

Signed-off-by: Biwen Li <biwen.li@nxp.com>

Support I2C_SLAVE_STOP event for the read transactions(master read from slave)

Signed-off-by: Biwen Li <biwen.li@nxp.com>

Fix warning as follows,
drivers/i2c/busses/i2c-imx.c:1046:7: warning: unused variable ‘enable_runtime_pm’ [-Wunused-variable]
  bool enable_runtime_pm = false;

Signed-off-by: Biwen Li <biwen.li@nxp.com>

The patch supports slave mode for imx I2C driver

Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>

Based on the I2C specification, if the data line (SDA) is stuck low,
the master should send nine clock pulses. The I2C slave device that
held the bus low should release it sometime within those nine clocks.

Because pinctrl is not supported on Layerscape, current bus recovery
is not avalible for Layerscape. This patch uses an open drain GPIO
pin to connect to the IICx_SCL to drive nine clock pulses to unlock
the I2C bus.

Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>

ERR010027: Attempting a start cycle while the bus is busy may
generate a short clock pulse.

Software must ensure that the I2C BUS is idle by checking the
bus busy before switching to master mode and attempting a Start
cycle.

Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
[ Aisheng: fix big conflict due to
3a5ee18d ("i2c: imx: implement master_xfer_atomic callback") ]
Sign-off-by: Dong Aisheng <aisheng.dong@nxp.com>

DMA might not be available yet when the i2c device probes.
Properly handle EPROBE_DEFER on dma channel allocation by
passing on this error.

Signed-off-by: Peng Ma <peng.ma@nxp.com>

Switching the clock frequently will affect the data transmission
efficiency, and prolong the timeout to reduce autosuspend times for
i2c-imx.

Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>

"i2c_clk_rate / 2" might be zero when the i2c_clk_rate gets the clock is
0 or 1, so add a judgment to avoid the denominator is equal to 0.

Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
[Arul: Add support to check return value everywhere in the driver]
Signed-off-by: Arulpandiyan Vadivel <arulpandiyan_vadivel@mentor.com>

Signed-off-by: Shrikant Bobade <Shrikant_Bobade@mentor.com>
(cherry picked from commit d382de595bffc0975ab7c0582e08dd4f7afc0c1a)
(cherry picked from commit 456caa9b)

According the e7805 in Errata, the SCK low level period should be less
than 1.3us.

The other series platform use this same IP can match the errata, and
ensure the low level period longer than 1.3us when the speed set to
400KHz. However, only at imx7d platform, the low level period is less
than 1.3us in the same situation.

Therefore, limit the maximum transfer speed to 384KHz when probe at
imx7d platform.

Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
(cherry picked from commit 19f553846e872b5c379b37ed029132b79566cab0)
(cherry picked from commit 5d355407)

When we do system suspend, the runtime pm will be disabled, but we need
to control the PMIC to power on/off the regulator, if the runtime pm is
disabled, if will failed to request runtime wakeup. So data transfer will
failed.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
(cherry picked from commit 93adab71)
[ Aisheng: fix big conflict due to 
3a5ee18d ("i2c: imx: implement master_xfer_atomic callback") ]
Sign-off-by: Dong Aisheng <aisheng.dong@nxp.com>

restore pin setting for i2c in suspend/resume

Signed-off-by: Gao Pan <gaopan@freescale.com>
(Vipul: Fixed merge conflicts)
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
(cherry picked from commit 42b5aa1d)

The i2c irq is masked when pcie starts a i2c transfer process
during noirq suspend stage. As a result, i2c transfer fails.
To solve the problem, IRQF_NO_SUSPEND is added to i2c bus.

Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
(cherry picked from commit d21259d9)

If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.

So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.

Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
                           # the 3rd argument from the calls to
                           # i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.

Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>

According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().

Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This reverts commit fa4d3055. An updated
version was sent. So, revert this version and give the new version more
time for testing.

Signed-off-by: Wolfram Sang <wsa@kernel.org>

According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().

Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>

If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled.  This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):

    Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
    Internal error: : 1008 [#1] ARM
    Modules linked in:
    CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
    Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
      (i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
      (free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
      (release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
      (really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
      (driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
      (device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
      (__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
      (bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
      (bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
      (driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
      (do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
      (kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
      (kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)

Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.

The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.

Fixes: 1c4b6c3b ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Since we have generic definitions for bus frequencies, let's use them.

Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Robert Richter <rrichter@marvell.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Elie Morisse <syniurge@gmail.com>
Acked-by: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

We don't need dev_err() message because when something goes wrong,
platform_get_irq() has print an error message itself, so we should
remove duplicate dev_err().

Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Rework the read and write code paths in the driver to support operation
in atomic contexts. To achieve this, the driver must not rely on IRQs
and not call schedule(), e.g. via a sleep routine, in these cases.

With this patch the driver supports normal operation, DMA transfers and
now the polling mode or also called sleep-free or IRQ-less operation. It
makes the code not simpler or easier to read, but atomic I2C transfers
are needed on some hardware configurations, e.g. to trigger reboots on
an external PMIC chip.

Signed-off-by: Stefan Lengfeld <contact@stefanchrist.eu>
[m.felsch@pengutronix.de: integrate https://patchwork.ozlabs.org/patch/1085943/

 review feedback]
[m.felsch@pengutronix.de: adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Enable NXP i2c controller to boot with ACPI.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Since commit e1ab9a46 ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") when booting with the DMA driver as module (such
as CONFIG_FSL_EDMA=m) the following endless clk warnings are seen:

[  153.077831] ------------[ cut here ]------------
[  153.082528] WARNING: CPU: 0 PID: 15 at drivers/clk/clk.c:924 clk_core_disable_lock+0x18/0x24
[  153.093077] i2c0 already disabled
[  153.096416] Modules linked in:
[  153.099521] CPU: 0 PID: 15 Comm: kworker/0:1 Tainted: G        W         5.2.0+ #321
[  153.107290] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[  153.113772] Workqueue: events deferred_probe_work_func
[  153.118979] [<c0019560>] (unwind_backtrace) from [<c0014734>] (show_stack+0x10/0x14)
[  153.126778] [<c0014734>] (show_stack) from [<c083f8dc>] (dump_stack+0x9c/0xd4)
[  153.134051] [<c083f8dc>] (dump_stack) from [<c0031154>] (__warn+0xf8/0x124)
[  153.141056] [<c0031154>] (__warn) from [<c0031248>] (warn_slowpath_fmt+0x38/0x48)
[  153.148580] [<c0031248>] (warn_slowpath_fmt) from [<c040fde0>] (clk_core_disable_lock+0x18/0x24)
[  153.157413] [<c040fde0>] (clk_core_disable_lock) from [<c058f520>] (i2c_imx_probe+0x554/0x6ec)
[  153.166076] [<c058f520>] (i2c_imx_probe) from [<c04b9178>] (platform_drv_probe+0x48/0x98)
[  153.174297] [<c04b9178>] (platform_drv_probe) from [<c04b7298>] (really_probe+0x1d8/0x2c0)
[  153.182605] [<c04b7298>] (really_probe) from [<c04b7554>] (driver_probe_device+0x5c/0x174)
[  153.190909] [<c04b7554>] (driver_probe_device) from [<c04b58c8>] (bus_for_each_drv+0x44/0x8c)
[  153.199480] [<c04b58c8>] (bus_for_each_drv) from [<c04b746c>] (__device_attach+0xa0/0x108)
[  153.207782] [<c04b746c>] (__device_attach) from [<c04b65a4>] (bus_probe_device+0x88/0x90)
[  153.215999] [<c04b65a4>] (bus_probe_device) from [<c04b6a04>] (deferred_probe_work_func+0x60/0x90)
[  153.225003] [<c04b6a04>] (deferred_probe_work_func) from [<c004f190>] (process_one_work+0x204/0x634)
[  153.234178] [<c004f190>] (process_one_work) from [<c004f618>] (worker_thread+0x20/0x484)
[  153.242315] [<c004f618>] (worker_thread) from [<c0055c2c>] (kthread+0x118/0x150)
[  153.249758] [<c0055c2c>] (kthread) from [<c00090b4>] (ret_from_fork+0x14/0x20)
[  153.257006] Exception stack(0xdde43fb0 to 0xdde43ff8)
[  153.262095] 3fa0:                                     00000000 00000000 00000000 00000000
[  153.270306] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  153.278520] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[  153.285159] irq event stamp: 3323022
[  153.288787] hardirqs last  enabled at (3323021): [<c0861c4c>] _raw_spin_unlock_irq+0x24/0x2c
[  153.297261] hardirqs last disabled at (3323022): [<c040d7a0>] clk_enable_lock+0x10/0x124
[  153.305392] softirqs last  enabled at (3322092): [<c000a504>] __do_softirq+0x344/0x540
[  153.313352] softirqs last disabled at (3322081): [<c00385c0>] irq_exit+0x10c/0x128
[  153.320946] ---[ end trace a506731ccd9bd703 ]---

This endless clk warnings behaviour is well explained by Andrey Smirnov:

"Allocating DMA after registering I2C adapter can lead to infinite
probing loop, for example, consider the following scenario:

    1. i2c_imx_probe() is called and successfully registers an I2C
       adapter via i2c_add_numbered_adapter()

    2. As a part of i2c_add_numbered_adapter() new I2C slave devices
       are added from DT which results in a call to
       driver_deferred_probe_trigger()

    3. i2c_imx_probe() continues and calls i2c_imx_dma_request() which
       due to lack of proper DMA driver returns -EPROBE_DEFER

    4. i2c_imx_probe() fails, removes I2C adapter and returns
       -EPROBE_DEFER, which places it into deferred probe list

    5. Deferred probe work triggered in #2 above kicks in and calls
       i2c_imx_probe() again thus bringing us to step #1"

So revert commit e1ab9a46 ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") and restore the old behaviour, in order to
avoid regressions on existing setups.

Cc: <stable@vger.kernel.org>
Reported-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e1ab9a46 ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use __maybe_unused for runtime PM related functions instead
of #if CONFIG_PM to simply the code.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The way of getting private imx_i2c_struct in i2c_imx_clk_notifier_call()
is incorrect, should use clk_change_nb element to get correct address
and avoid below kernel dump during POST_RATE_CHANGE notify by clk
framework:

Unable to handle kernel paging request at virtual address 03ef1488
pgd = (ptrval)
[03ef1488] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: events reduce_bus_freq_handler
PC is at i2c_imx_set_clk+0x10/0xb8
LR is at i2c_imx_clk_notifier_call+0x20/0x28
pc : [<806a893c>]    lr : [<806a8a04>]    psr: a0080013
sp : bf399dd8  ip : bf3432ac  fp : bf7c1dc0
r10: 00000002  r9 : 00000000  r8 : 00000000
r7 : 03ef1480  r6 : bf399e50  r5 : ffffffff  r4 : 00000000
r3 : bf025300  r2 : bf399e50  r1 : 00b71b00  r0 : bf399be8
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 4e03004a  DAC: 00000051
Process kworker/2:1 (pid: 38, stack limit = 0x(ptrval))
Stack: (0xbf399dd8 to 0xbf39a000)
9dc0:                                                       806a89e4 00000000
9de0: ffffffff bf399e50 00000002 806a8a04 806a89e4 80142900 ffffffff 00000000
9e00: bf34ef18 bf34ef04 00000000 ffffffff bf399e50 80142d84 00000000 bf399e6c
9e20: bf34ef00 80f214c4 bf025300 00000002 80f08d08 bf017480 00000000 80142df0
9e40: 00000000 80166ed8 80c27638 8045de58 bf352340 03ef1480 00b71b00 0f82e242
9e60: bf025300 00000002 03ef1480 80f60e5c 00000001 8045edf0 00000002 8045eb08
9e80: bf025300 00000002 03ef1480 8045ee10 03ef1480 8045eb08 bf01be40 00000002
9ea0: 03ef1480 8045ee10 07de2900 8045eb08 bf01b780 00000002 07de2900 8045ee10
9ec0: 80c27898 bf399ee4 bf020a80 00000002 1f78a400 8045ee10 80f60e5c 80460514
9ee0: 80f60e5c bf01b600 bf01b480 80460460 0f82e242 bf383a80 bf383a00 80f60e5c
9f00: 00000000 bf7c1dc0 80f60e70 80460564 80f60df0 80f60d24 80f60df0 8011e72c
9f20: 00000000 80f60df0 80f60e6c bf7c4f00 00000000 8011e7ac bf274000 8013bd84
9f40: bf7c1dd8 80f03d00 bf274000 bf7c1dc0 bf274014 bf7c1dd8 80f03d00 bf398000
9f60: 00000008 8013bfb4 00000000 bf25d100 bf25d0c0 00000000 bf274000 8013bf88
9f80: bf25d11c bf0cfebc 00000000 8014140c bf25d0c0 801412ec 00000000 00000000
9fa0: 00000000 00000000 00000000 801010e8 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<806a893c>] (i2c_imx_set_clk) from [<806a8a04>] (i2c_imx_clk_notifier_call+0x20/0x28)
[<806a8a04>] (i2c_imx_clk_notifier_call) from [<80142900>] (notifier_call_chain+0x44/0x84)
[<80142900>] (notifier_call_chain) from [<80142d84>] (__srcu_notifier_call_chain+0x44/0x98)
[<80142d84>] (__srcu_notifier_call_chain) from [<80142df0>] (srcu_notifier_call_chain+0x18/0x20)
[<80142df0>] (srcu_notifier_call_chain) from [<8045de58>] (__clk_notify+0x78/0xa4)
[<8045de58>] (__clk_notify) from [<8045edf0>] (__clk_recalc_rates+0x60/0xb4)
[<8045edf0>] (__clk_recalc_rates) from [<8045ee10>] (__clk_recalc_rates+0x80/0xb4)
Code: e92d40f8 e5903298 e59072a0 e1530001 (e5975008)
---[ end trace fc7f5514b97b6cbb ]---

Fixes: 90ad2cbe ("i2c: imx: use clk notifier for rate changes")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Make sure to free the i2c adapter on the error exit path.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: e1ab9a46 ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Change the call to PTR_ERR to access the value just tested by IS_ERR.

Fixes: 5b3a23a3 ("i2c: imx: notify about real errors on dma i2c_imx_dma_request")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Improve the error handling in i2c_imx_dma_request() and let it return an error
indication that the caller then can handle accordingly.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

At least on i.MX5x, the DMA events for I2C and SDHC use the same channel
and there can only be a single user. So in this case there should be no
message emitted that looks like an error if the I2C device doesn't have
an assigned DMA channel. In contrast real problems that were only
emitted at debug level before should be described at a higher level
to be better visible and so understandable.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Probe deferral is a normal operating condition in the probe function,
so don't spam the log with an error in this case.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().

Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read.  When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).

Fixed by setting the DMAEN bit before the dummy read.

Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

I2C is open drain, so request the GPIO accordingly, even if pinmux did
set it up correctly for in-kernel users in this case.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>