Merge branch 'davinci-for-linus' of...

Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci

* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
  davinci: fix remaining board support after io_pgoffst removal
  davinci: mityomapl138: make file local data static
  arm/davinci: remove duplicated include
  davinci: Initial support for Omapl138-Hawkboard
  davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
  davinci: add tnetv107x touchscreen platform device
  input: add driver for tnetv107x touchscreen controller
  davinci: add keypad config for tnetv107x evm board
  davinci: add tnetv107x keypad platform device
  input: add driver for tnetv107x on-chip keypad controller
  net: davinci_emac: cleanup unused cpdma code
  net: davinci_emac: switch to new cpdma layer
  net: davinci_emac: separate out cpdma code
  net: davinci_emac: cleanup unused mdio emac code
  omap: cleanup unused davinci mdio arch code
  davinci: cleanup mdio arch code and switch to phy_id
  net: davinci_emac: switch to new mdio
  omap: add mdio platform devices
  davinci: add mdio platform devices
  net: davinci_emac: separate out davinci mdio
  ...

Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)

MAINTAINERS

@@ -5388,8 +5388,8 @@ F:	drivers/*/*s3c2410*
 F:	drivers/*/*/*s3c2410*
 
 TI DAVINCI MACHINE SUPPORT
-P:	Kevin Hilman
-M:	davinci-linux-open-source@linux.davincidsp.com
+M:	Kevin Hilman <khilman@deeprootsystems.com>
+L:	davinci-linux-open-source@linux.davincidsp.com (subscribers-only)
 Q:	http://patchwork.kernel.org/project/linux-davinci/list/
 S:	Supported
 F:	arch/arm/mach-davinci

arch/arm/configs/da8xx_omapl_defconfig

@@ -17,6 +17,8 @@ CONFIG_MODVERSIONS=y
 CONFIG_ARCH_DAVINCI=y
 CONFIG_ARCH_DAVINCI_DA830=y
 CONFIG_ARCH_DAVINCI_DA850=y
+CONFIG_MACH_MITYOMAPL138=y
+CONFIG_MACH_OMAPL138_HAWKBOARD=y
 CONFIG_DAVINCI_RESET_CLOCKS=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -79,6 +81,7 @@ CONFIG_I2C_DAVINCI=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DUMMY=y
 CONFIG_REGULATOR_TPS6507X=y
 CONFIG_FB=y
 CONFIG_FB_DA8XX=y

arch/arm/mach-davinci/Kconfig

@@ -20,23 +20,23 @@ config ARCH_DAVINCI_DM644x
 	select ARCH_DAVINCI_DMx
 
 config ARCH_DAVINCI_DM355
-        bool "DaVinci 355 based system"
+	bool "DaVinci 355 based system"
 	select AINTC
 	select ARCH_DAVINCI_DMx
 
 config ARCH_DAVINCI_DM646x
-        bool "DaVinci 646x based system"
+	bool "DaVinci 646x based system"
 	select AINTC
 	select ARCH_DAVINCI_DMx
 
 config ARCH_DAVINCI_DA830
-        bool "DA830/OMAP-L137 based system"
+	bool "DA830/OMAP-L137/AM17x based system"
 	select CP_INTC
 	select ARCH_DAVINCI_DA8XX
 	select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1
 
 config ARCH_DAVINCI_DA850
-	bool "DA850/OMAP-L138 based system"
+	bool "DA850/OMAP-L138/AM18x based system"
 	select CP_INTC
 	select ARCH_DAVINCI_DA8XX
 	select ARCH_HAS_CPUFREQ
@@ -115,21 +115,21 @@ config MACH_DAVINCI_DM365_EVM
 	  for development is a DM365 EVM
 
 config MACH_DAVINCI_DA830_EVM
-	bool "TI DA830/OMAP-L137 Reference Platform"
+	bool "TI DA830/OMAP-L137/AM17x Reference Platform"
 	default ARCH_DAVINCI_DA830
 	depends on ARCH_DAVINCI_DA830
 	select GPIO_PCF857X
 	help
-	  Say Y here to select the TI DA830/OMAP-L137 Evaluation Module.
+	  Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module.
 
 choice
-	prompt "Select DA830/OMAP-L137 UI board peripheral"
+	prompt "Select DA830/OMAP-L137/AM17x UI board peripheral"
 	depends on MACH_DAVINCI_DA830_EVM
 	help
-	  The presence of UI card on the DA830/OMAP-L137 EVM is detected
-	  automatically based on successful probe of the I2C based GPIO
-	  expander on that board. This option selected in this menu has
-	  an effect only in case of a successful UI card detection.
+	  The presence of UI card on the DA830/OMAP-L137/AM17x EVM is
+	  detected automatically based on successful probe of the I2C
+	  based GPIO expander on that board. This option selected in this
+	  menu has an effect only in case of a successful UI card detection.
 
 config DA830_UI_LCD
 	bool "LCD"
@@ -140,23 +140,23 @@ config DA830_UI_LCD
 config DA830_UI_NAND
 	bool "NAND flash"
 	help
-	  Say Y here to use the NAND flash.  Do not forget to setup
+	  Say Y here to use the NAND flash. Do not forget to setup
 	  the switch correctly.
 endchoice
 
 config MACH_DAVINCI_DA850_EVM
-	bool "TI DA850/OMAP-L138 Reference Platform"
+	bool "TI DA850/OMAP-L138/AM18x Reference Platform"
 	default ARCH_DAVINCI_DA850
 	depends on ARCH_DAVINCI_DA850
 	select GPIO_PCA953X
 	help
-	  Say Y here to select the TI DA850/OMAP-L138 Evaluation Module.
+	  Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module.
 
 choice
 	prompt "Select peripherals connected to expander on UI board"
 	depends on MACH_DAVINCI_DA850_EVM
 	help
-	  The presence of User Interface (UI) card on the DA850/OMAP-L138
+	  The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x
 	  EVM is detected automatically based on successful probe of the I2C
 	  based GPIO expander on that card. This option selected in this
 	  menu has an effect only in case of a successful UI card detection.
@@ -165,13 +165,13 @@ config DA850_UI_NONE
 	bool "No peripheral is enabled"
 	help
 	  Say Y if you do not want to enable any of the peripherals connected
-	  to TCA6416 expander on DA850/OMAP-L138 EVM UI card
+	  to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card
 
 config DA850_UI_RMII
 	bool "RMII Ethernet PHY"
 	help
-	  Say Y if you want to use the RMII PHY on the DA850/OMAP-L138 EVM.
-	  This PHY is found on the UI daughter card that is supplied with
+	  Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x
+	  EVM. This PHY is found on the UI daughter card that is supplied with
 	  the EVM.
 	  NOTE: Please take care while choosing this option, MII PHY will
 	  not be functional if RMII mode is selected.
@@ -185,6 +185,22 @@ config MACH_TNETV107X
 	help
 	  Say Y here to select the TI TNETV107X Evaluation Module.
 
+config MACH_MITYOMAPL138
+	bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
+	depends on ARCH_DAVINCI_DA850
+	help
+	  Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
+	  System on Module.  Information on this SoM may be found at
+	  http://www.mitydsp.com
+
+config MACH_OMAPL138_HAWKBOARD
+	bool "TI AM1808 / OMAPL-138 Hawkboard platform"
+	depends on ARCH_DAVINCI_DA850
+	help
+	  Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
+	  Information of this board may be found at
+	  http://www.hawkboard.org/
+
 config DAVINCI_MUX
 	bool "DAVINCI multiplexing support"
 	depends on ARCH_DAVINCI
@@ -195,20 +211,20 @@ config DAVINCI_MUX
 	  say Y.
 
 config DAVINCI_MUX_DEBUG
-        bool "Multiplexing debug output"
-        depends on DAVINCI_MUX
-        help
-          Makes the multiplexing functions print out a lot of debug info.
-          This is useful if you want to find out the correct values of the
-          multiplexing registers.
+	bool "Multiplexing debug output"
+	depends on DAVINCI_MUX
+	help
+	  Makes the multiplexing functions print out a lot of debug info.
+	  This is useful if you want to find out the correct values of the
+	  multiplexing registers.
 
 config DAVINCI_MUX_WARNINGS
-        bool "Warn about pins the bootloader didn't set up"
-        depends on DAVINCI_MUX
-        help
-          Choose Y here to warn whenever driver initialization logic needs
-          to change the pin multiplexing setup.  When there are no warnings
-          printed, it's safe to deselect DAVINCI_MUX for your product.
+	bool "Warn about pins the bootloader didn't set up"
+	depends on DAVINCI_MUX
+	help
+	  Choose Y here to warn whenever driver initialization logic needs
+	  to change the pin multiplexing setup. When there are no warnings
+	  printed, it's safe to deselect DAVINCI_MUX for your product.
 
 config DAVINCI_RESET_CLOCKS
 	bool "Reset unused clocks during boot"

arch/arm/mach-davinci/Makefile

@@ -5,7 +5,7 @@
 
 # Common objects
 obj-y 			:= time.o clock.o serial.o io.o psc.o \
-			   gpio.o dma.o usb.o common.o sram.o
+			   gpio.o dma.o usb.o common.o sram.o aemif.o
 
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
@@ -33,6 +33,8 @@ obj-$(CONFIG_MACH_DAVINCI_DM365_EVM)	+= board-dm365-evm.o
 obj-$(CONFIG_MACH_DAVINCI_DA830_EVM)	+= board-da830-evm.o
 obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= board-da850-evm.o
 obj-$(CONFIG_MACH_TNETV107X)		+= board-tnetv107x-evm.o
+obj-$(CONFIG_MACH_MITYOMAPL138)		+= board-mityomapl138.o
+obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD)	+= board-omapl138-hawk.o
 
 # Power Management
 obj-$(CONFIG_CPU_FREQ)			+= cpufreq.o

arch/arm/mach-davinci/aemif.c

+/*
+ * AEMIF support for DaVinci SoCs
+ *
+ * Copyright (C) 2010 Texas Instruments Incorporated. http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/time.h>
+
+#include <mach/aemif.h>
+
+/* Timing value configuration */
+
+#define TA(x)		((x) << 2)
+#define RHOLD(x)	((x) << 4)
+#define RSTROBE(x)	((x) << 7)
+#define RSETUP(x)	((x) << 13)
+#define WHOLD(x)	((x) << 17)
+#define WSTROBE(x)	((x) << 20)
+#define WSETUP(x)	((x) << 26)
+
+#define TA_MAX		0x3
+#define RHOLD_MAX	0x7
+#define RSTROBE_MAX	0x3f
+#define RSETUP_MAX	0xf
+#define WHOLD_MAX	0x7
+#define WSTROBE_MAX	0x3f
+#define WSETUP_MAX	0xf
+
+#define TIMING_MASK	(TA(TA_MAX) | \
+				RHOLD(RHOLD_MAX) | \
+				RSTROBE(RSTROBE_MAX) |	\
+				RSETUP(RSETUP_MAX) | \
+				WHOLD(WHOLD_MAX) | \
+				WSTROBE(WSTROBE_MAX) | \
+				WSETUP(WSETUP_MAX))
+
+/*
+ * aemif_calc_rate - calculate timing data.
+ * @wanted: The cycle time needed in nanoseconds.
+ * @clk: The input clock rate in kHz.
+ * @max: The maximum divider value that can be programmed.
+ *
+ * On success, returns the calculated timing value minus 1 for easy
+ * programming into AEMIF timing registers, else negative errno.
+ */
+static int aemif_calc_rate(int wanted, unsigned long clk, int max)
+{
+	int result;
+
+	result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1;
+
+	pr_debug("%s: result %d from %ld, %d\n", __func__, result, clk, wanted);
+
+	/* It is generally OK to have a more relaxed timing than requested... */
+	if (result < 0)
+		result = 0;
+
+	/* ... But configuring tighter timings is not an option. */
+	else if (result > max)
+		result = -EINVAL;
+
+	return result;
+}
+
+/**
+ * davinci_aemif_setup_timing - setup timing values for a given AEMIF interface
+ * @t: timing values to be progammed
+ * @base: The virtual base address of the AEMIF interface
+ * @cs: chip-select to program the timing values for
+ *
+ * This function programs the given timing values (in real clock) into the
+ * AEMIF registers taking the AEMIF clock into account.
+ *
+ * This function does not use any locking while programming the AEMIF
+ * because it is expected that there is only one user of a given
+ * chip-select.
+ *
+ * Returns 0 on success, else negative errno.
+ */
+int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
+					void __iomem *base, unsigned cs)
+{
+	unsigned set, val;
+	unsigned ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup;
+	unsigned offset = A1CR_OFFSET + cs * 4;
+	struct clk *aemif_clk;
+	unsigned long clkrate;
+
+	if (!t)
+		return 0;	/* Nothing to do */
+
+	aemif_clk = clk_get(NULL, "aemif");
+	if (IS_ERR(aemif_clk))
+		return PTR_ERR(aemif_clk);
+
+	clkrate = clk_get_rate(aemif_clk);
+
+	clkrate /= 1000;	/* turn clock into kHz for ease of use */
+
+	ta	= aemif_calc_rate(t->ta, clkrate, TA_MAX);
+	rhold	= aemif_calc_rate(t->rhold, clkrate, RHOLD_MAX);
+	rstrobe	= aemif_calc_rate(t->rstrobe, clkrate, RSTROBE_MAX);
+	rsetup	= aemif_calc_rate(t->rsetup, clkrate, RSETUP_MAX);
+	whold	= aemif_calc_rate(t->whold, clkrate, WHOLD_MAX);
+	wstrobe	= aemif_calc_rate(t->wstrobe, clkrate, WSTROBE_MAX);
+	wsetup	= aemif_calc_rate(t->wsetup, clkrate, WSETUP_MAX);
+
+	if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 ||
+			whold < 0 || wstrobe < 0 || wsetup < 0) {
+		pr_err("%s: cannot get suitable timings\n", __func__);
+		return -EINVAL;
+	}
+
+	set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) |
+		WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup);
+
+	val = __raw_readl(base + offset);
+	val &= ~TIMING_MASK;
+	val |= set;
+	__raw_writel(val, base + offset);
+
+	return 0;
+}
+EXPORT_SYMBOL(davinci_aemif_setup_timing);

arch/arm/mach-davinci/board-da830-evm.c

@@ -29,10 +29,9 @@
 #include <mach/nand.h>
 #include <mach/da8xx.h>
 #include <mach/usb.h>
+#include <mach/aemif.h>
 
-#define DA830_EVM_PHY_MASK		0x0
-#define DA830_EVM_MDIO_FREQUENCY	2200000	/* PHY bus frequency */
-
+#define DA830_EVM_PHY_ID		""
 /*
  * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
  */
@@ -360,6 +359,16 @@ static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
 	.pattern	= da830_evm_nand_mirror_pattern
 };
 
+static struct davinci_aemif_timing da830_evm_nandflash_timing = {
+	.wsetup         = 24,
+	.wstrobe        = 21,
+	.whold          = 14,
+	.rsetup         = 19,
+	.rstrobe        = 50,
+	.rhold          = 0,
+	.ta             = 20,
+};
+
 static struct davinci_nand_pdata da830_evm_nand_pdata = {
 	.parts		= da830_evm_nand_partitions,
 	.nr_parts	= ARRAY_SIZE(da830_evm_nand_partitions),
@@ -368,6 +377,7 @@ static struct davinci_nand_pdata da830_evm_nand_pdata = {
 	.options	= NAND_USE_FLASH_BBT,
 	.bbt_td		= &da830_evm_nand_bbt_main_descr,
 	.bbt_md		= &da830_evm_nand_bbt_mirror_descr,
+	.timing         = &da830_evm_nandflash_timing,
 };
 
 static struct resource da830_evm_nand_resources[] = {
@@ -546,9 +556,8 @@ static __init void da830_evm_init(void)
 
 	da830_evm_usb_init();
 
-	soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK;
-	soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY;
 	soc_info->emac_pdata->rmii_en = 1;
+	soc_info->emac_pdata->phy_id = DA830_EVM_PHY_ID;
 
 	ret = davinci_cfg_reg_list(da830_cpgmac_pins);
 	if (ret)
@@ -586,6 +595,9 @@ static __init void da830_evm_init(void)
 #ifdef CONFIG_SERIAL_8250_CONSOLE
 static int __init da830_evm_console_init(void)
 {
+	if (!machine_is_davinci_da830_evm())
+		return 0;
+
 	return add_preferred_console("ttyS", 2, "115200");
 }
 console_initcall(da830_evm_console_init);
@@ -596,7 +608,7 @@ static void __init da830_evm_map_io(void)
 	da830_init();
 }
 
-MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM")
+MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
 	.boot_params	= (DA8XX_DDR_BASE + 0x100),
 	.map_io		= da830_evm_map_io,
 	.init_irq	= cp_intc_init,

arch/arm/mach-davinci/board-da850-evm.c

@@ -26,7 +26,6 @@
 #include <linux/mtd/physmap.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/tps6507x.h>
-#include <linux/mfd/tps6507x.h>
 #include <linux/input/tps6507x-ts.h>
 
 #include <asm/mach-types.h>
@@ -36,10 +35,9 @@
 #include <mach/da8xx.h>
 #include <mach/nand.h>
 #include <mach/mux.h>
+#include <mach/aemif.h>
 
-#define DA850_EVM_PHY_MASK		0x1
-#define DA850_EVM_MDIO_FREQUENCY	2200000 /* PHY bus frequency */
-
+#define DA850_EVM_PHY_ID		"0:00"
 #define DA850_LCD_PWR_PIN		GPIO_TO_PIN(2, 8)
 #define DA850_LCD_BL_PIN		GPIO_TO_PIN(2, 15)
 
@@ -110,7 +108,7 @@ static struct platform_device da850_pm_device = {
  * to boot, using TI's tools to install the secondary boot loader
  * (UBL) and U-Boot.
  */
-struct mtd_partition da850_evm_nandflash_partition[] = {
+static struct mtd_partition da850_evm_nandflash_partition[] = {
 	{
 		.name		= "u-boot env",
 		.offset		= 0,
@@ -143,12 +141,23 @@ struct mtd_partition da850_evm_nandflash_partition[] = {
 	},
 };
 
+static struct davinci_aemif_timing da850_evm_nandflash_timing = {
+	.wsetup		= 24,
+	.wstrobe	= 21,
+	.whold		= 14,
+	.rsetup		= 19,
+	.rstrobe	= 50,
+	.rhold		= 0,
+	.ta		= 20,
+};
+
 static struct davinci_nand_pdata da850_evm_nandflash_data = {
 	.parts		= da850_evm_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(da850_evm_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
 	.ecc_bits	= 4,
 	.options	= NAND_USE_FLASH_BBT,
+	.timing		= &da850_evm_nandflash_timing,
 };
 
 static struct resource da850_evm_nandflash_resource[] = {
@@ -196,6 +205,30 @@ static void __init da850_evm_init_nor(void)
 	iounmap(aemif_addr);
 }
 
+static const short da850_evm_nand_pins[] = {
+	DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3,
+	DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7,
+	DA850_EMA_A_1, DA850_EMA_A_2, DA850_NEMA_CS_3, DA850_NEMA_CS_4,
+	DA850_NEMA_WE, DA850_NEMA_OE,
+	-1
+};
+
+static const short da850_evm_nor_pins[] = {
+	DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2,
+	DA850_NEMA_WE, DA850_NEMA_OE, DA850_EMA_D_0, DA850_EMA_D_1,
+	DA850_EMA_D_2, DA850_EMA_D_3, DA850_EMA_D_4, DA850_EMA_D_5,
+	DA850_EMA_D_6, DA850_EMA_D_7, DA850_EMA_D_8, DA850_EMA_D_9,
+	DA850_EMA_D_10, DA850_EMA_D_11, DA850_EMA_D_12, DA850_EMA_D_13,
+	DA850_EMA_D_14, DA850_EMA_D_15, DA850_EMA_A_0, DA850_EMA_A_1,
+	DA850_EMA_A_2, DA850_EMA_A_3, DA850_EMA_A_4, DA850_EMA_A_5,
+	DA850_EMA_A_6, DA850_EMA_A_7, DA850_EMA_A_8, DA850_EMA_A_9,
+	DA850_EMA_A_10, DA850_EMA_A_11, DA850_EMA_A_12, DA850_EMA_A_13,
+	DA850_EMA_A_14, DA850_EMA_A_15, DA850_EMA_A_16, DA850_EMA_A_17,
+	DA850_EMA_A_18, DA850_EMA_A_19, DA850_EMA_A_20, DA850_EMA_A_21,
+	DA850_EMA_A_22, DA850_EMA_A_23,
+	-1
+};
+
 static u32 ui_card_detected;
 
 #if defined(CONFIG_MMC_DAVINCI) || \
@@ -205,17 +238,17 @@ static u32 ui_card_detected;
 #define HAS_MMC 0
 #endif
 
-static __init void da850_evm_setup_nor_nand(void)
+static inline void da850_evm_setup_nor_nand(void)
 {
 	int ret = 0;
 
 	if (ui_card_detected & !HAS_MMC) {
-		ret = davinci_cfg_reg_list(da850_nand_pins);
+		ret = davinci_cfg_reg_list(da850_evm_nand_pins);
 		if (ret)
 			pr_warning("da850_evm_init: nand mux setup failed: "
 					"%d\n", ret);
 
-		ret = davinci_cfg_reg_list(da850_nor_pins);
+		ret = davinci_cfg_reg_list(da850_evm_nor_pins);
 		if (ret)
 			pr_warning("da850_evm_init: nor mux setup failed: %d\n",
 				ret);
@@ -406,7 +439,7 @@ static int da850_lcd_hw_init(void)
 /* TPS65070 voltage regulator support */
 
 /* 3.3V */
-struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
+static struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
 	{
 		.supply = "usb0_vdda33",
 	},
@@ -416,7 +449,7 @@ struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
 };
 
 /* 3.3V or 1.8V */
-struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
+static struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
 	{
 		.supply = "dvdd3318_a",
 	},
@@ -429,14 +462,14 @@ struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
 };
 
 /* 1.2V */
-struct regulator_consumer_supply tps65070_dcdc3_consumers[] = {
+static struct regulator_consumer_supply tps65070_dcdc3_consumers[] = {
 	{
 		.supply = "cvdd",
 	},
 };
 
 /* 1.8V LDO */
-struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
+static struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
 	{
 		.supply = "sata_vddr",
 	},
@@ -452,7 +485,7 @@ struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
 };
 
 /* 1.2V LDO */
-struct regulator_consumer_supply tps65070_ldo2_consumers[] = {
+static struct regulator_consumer_supply tps65070_ldo2_consumers[] = {
 	{
 		.supply = "sata_vdd",
 	},
@@ -475,7 +508,7 @@ static struct tps6507x_reg_platform_data tps6507x_platform_data = {
 	.defdcdc_default = true,
 };
 
-struct regulator_init_data tps65070_regulator_data[] = {
+static struct regulator_init_data tps65070_regulator_data[] = {
 	/* dcdc1 */
 	{
 		.constraints = {
@@ -576,6 +609,23 @@ static const short da850_evm_lcdc_pins[] = {
 	-1
 };
 
+static const short da850_evm_mii_pins[] = {
+	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
+	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
+	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
+	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
+	DA850_MDIO_D,
+	-1
+};
+
+static const short da850_evm_rmii_pins[] = {
+	DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
+	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
+	DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
+	DA850_MDIO_D,
+	-1
+};
+
 static int __init da850_evm_config_emac(void)
 {
 	void __iomem *cfg_chip3_base;
@@ -593,12 +643,12 @@ static int __init da850_evm_config_emac(void)
 
 	if (rmii_en) {
 		val |= BIT(8);
-		ret = davinci_cfg_reg_list(da850_rmii_pins);
+		ret = davinci_cfg_reg_list(da850_evm_rmii_pins);
 		pr_info("EMAC: RMII PHY configured, MII PHY will not be"
 							" functional\n");
 	} else {
 		val &= ~BIT(8);
-		ret = davinci_cfg_reg_list(da850_cpgmac_pins);
+		ret = davinci_cfg_reg_list(da850_evm_mii_pins);
 		pr_info("EMAC: MII PHY configured, RMII PHY will not be"
 							" functional\n");
 	}
@@ -625,8 +675,7 @@ static int __init da850_evm_config_emac(void)
 	/* Enable/Disable MII MDIO clock */
 	gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, rmii_en);
 
-	soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK;
-	soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY;
+	soc_info->emac_pdata->phy_id = DA850_EVM_PHY_ID;
 
 	ret = da8xx_register_emac();
 	if (ret)
@@ -787,7 +836,7 @@ static __init void da850_evm_init(void)
 	if (ret)
 		pr_warning("da850_evm_init: rtc setup failed: %d\n", ret);
 
-	ret = da850_register_cpufreq();
+	ret = da850_register_cpufreq("pll0_sysclk3");
 	if (ret)
 		pr_warning("da850_evm_init: cpufreq registration failed: %d\n",
 				ret);
@@ -806,6 +855,9 @@ static __init void da850_evm_init(void)
 #ifdef CONFIG_SERIAL_8250_CONSOLE
 static int __init da850_evm_console_init(void)
 {
+	if (!machine_is_davinci_da850_evm())
+		return 0;
+
 	return add_preferred_console("ttyS", 2, "115200");
 }
 console_initcall(da850_evm_console_init);
@@ -816,7 +868,7 @@ static void __init da850_evm_map_io(void)
 	da850_init();
 }
 
-MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM")
+MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138/AM18x EVM")
 	.boot_params	= (DA8XX_DDR_BASE + 0x100),
 	.map_io		= da850_evm_map_io,
 	.init_irq	= cp_intc_init,

arch/arm/mach-davinci/board-dm365-evm.c

@@ -54,9 +54,7 @@ static inline int have_tvp7002(void)
 	return 0;
 }
 
-#define DM365_EVM_PHY_MASK		(0x2)
-#define DM365_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-
+#define DM365_EVM_PHY_ID		"0:01"
 /*
  * A MAX-II CPLD is used for various board control functions.
  */
@@ -175,7 +173,9 @@ static struct at24_platform_data eeprom_info = {
 	.context	= (void *)0x7f00,
 };
 
-static struct snd_platform_data dm365_evm_snd_data;
+static struct snd_platform_data dm365_evm_snd_data = {
+	.asp_chan_q = EVENTQ_3,
+};
 
 static struct i2c_board_info i2c_info[] = {
 	{
@@ -533,8 +533,7 @@ fail:
 
 		/* ... and ENET ... */
 		dm365evm_emac_configure();
-		soc_info->emac_pdata->phy_mask = DM365_EVM_PHY_MASK;
-		soc_info->emac_pdata->mdio_max_freq = DM365_EVM_MDIO_FREQUENCY;
+		soc_info->emac_pdata->phy_id = DM365_EVM_PHY_ID;
 		resets &= ~BIT(3);
 
 		/* ... and AIC33 */

arch/arm/mach-davinci/board-dm644x-evm.c

@@ -37,10 +37,9 @@
 #include <mach/nand.h>
 #include <mach/mmc.h>
 #include <mach/usb.h>
+#include <mach/aemif.h>
 
-#define DM644X_EVM_PHY_MASK		(0x2)
-#define DM644X_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-
+#define DM644X_EVM_PHY_ID		"0:01"
 #define LXT971_PHY_ID	(0x001378e2)
 #define LXT971_PHY_MASK	(0xfffffff0)
 
@@ -137,11 +136,22 @@ static struct mtd_partition davinci_evm_nandflash_partition[] = {
 	 */
 };
 
+static struct davinci_aemif_timing davinci_evm_nandflash_timing = {
+	.wsetup		= 20,
+	.wstrobe	= 40,
+	.whold		= 20,
+	.rsetup		= 10,
+	.rstrobe	= 40,
+	.rhold		= 10,
+	.ta		= 40,
+};
+
 static struct davinci_nand_pdata davinci_evm_nandflash_data = {
 	.parts		= davinci_evm_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(davinci_evm_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
 	.options	= NAND_USE_FLASH_BBT,
+	.timing		= &davinci_evm_nandflash_timing,
 };
 
 static struct resource davinci_evm_nandflash_resource[] = {
@@ -695,9 +705,7 @@ static __init void davinci_evm_init(void)
 	davinci_serial_init(&uart_config);
 	dm644x_init_asp(&dm644x_evm_snd_data);
 
-	soc_info->emac_pdata->phy_mask = DM644X_EVM_PHY_MASK;
-	soc_info->emac_pdata->mdio_max_freq = DM644X_EVM_MDIO_FREQUENCY;
-
+	soc_info->emac_pdata->phy_id = DM644X_EVM_PHY_ID;
 	/* Register the fixup for PHY on DaVinci */
 	phy_register_fixup_for_uid(LXT971_PHY_ID, LXT971_PHY_MASK,
 					davinci_phy_fixup);

arch/arm/mach-davinci/board-dm646x-evm.c

@@ -42,6 +42,7 @@
 #include <mach/nand.h>
 #include <mach/clock.h>
 #include <mach/cdce949.h>
+#include <mach/aemif.h>
 
 #include "clock.h"
 
@@ -71,6 +72,16 @@ static struct mtd_partition davinci_nand_partitions[] = {
 	}
 };
 
+static struct davinci_aemif_timing dm6467tevm_nandflash_timing = {
+	.wsetup		= 29,
+	.wstrobe	= 24,
+	.whold		= 14,
+	.rsetup		= 19,
+	.rstrobe	= 33,
+	.rhold		= 0,
+	.ta		= 29,
+};
+
 static struct davinci_nand_pdata davinci_nand_data = {
 	.mask_cle 		= 0x80000,
 	.mask_ale 		= 0x40000,
@@ -718,9 +729,7 @@ static struct davinci_uart_config uart_config __initdata = {
 	.enabled_uarts = (1 << 0),
 };
 
-#define DM646X_EVM_PHY_MASK		(0x2)
-#define DM646X_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-
+#define DM646X_EVM_PHY_ID		"0:01"
 /*
  * The following EDMA channels/slots are not being used by drivers (for
  * example: Timer, GPIO, UART events etc) on dm646x, hence they are being
@@ -763,6 +772,9 @@ static __init void evm_init(void)
 	dm646x_init_mcasp0(&dm646x_evm_snd_data[0]);
 	dm646x_init_mcasp1(&dm646x_evm_snd_data[1]);
 
+	if (machine_is_davinci_dm6467tevm())
+		davinci_nand_data.timing = &dm6467tevm_nandflash_timing;
+
 	platform_device_register(&davinci_nand_device);
 
 	dm646x_init_edma(dm646x_edma_rsv);
@@ -770,8 +782,7 @@ static __init void evm_init(void)
 	if (HAS_ATA)
 		davinci_init_ide();
 
-	soc_info->emac_pdata->phy_mask = DM646X_EVM_PHY_MASK;
-	soc_info->emac_pdata->mdio_max_freq = DM646X_EVM_MDIO_FREQUENCY;
+	soc_info->emac_pdata->phy_id = DM646X_EVM_PHY_ID;
 }
 
 #define DM646X_EVM_REF_FREQ		27000000

arch/arm/mach-davinci/board-mityomapl138.c

+/*
+ * Critical Link MityOMAP-L138 SoM
+ *
+ * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of
+ * any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/regulator/machine.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+#include <linux/etherdevice.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/common.h>
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+#include <mach/nand.h>
+#include <mach/mux.h>
+
+#define MITYOMAPL138_PHY_ID		"0:03"
+
+#define FACTORY_CONFIG_MAGIC	0x012C0138
+#define FACTORY_CONFIG_VERSION	0x00010001
+
+/* Data Held in On-Board I2C device */
+struct factory_config {
+	u32	magic;
+	u32	version;
+	u8	mac[6];
+	u32	fpga_type;
+	u32	spare;
+	u32	serialnumber;
+	char	partnum[32];
+};
+
+static struct factory_config factory_config;
+
+static void read_factory_config(struct memory_accessor *a, void *context)
+{
+	int ret;
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	ret = a->read(a, (char *)&factory_config, 0, sizeof(factory_config));
+	if (ret != sizeof(struct factory_config)) {
+		pr_warning("MityOMAPL138: Read Factory Config Failed: %d\n",
+				ret);
+		return;
+	}
+
+	if (factory_config.magic != FACTORY_CONFIG_MAGIC) {
+		pr_warning("MityOMAPL138: Factory Config Magic Wrong (%X)\n",
+				factory_config.magic);
+		return;
+	}
+
+	if (factory_config.version != FACTORY_CONFIG_VERSION) {
+		pr_warning("MityOMAPL138: Factory Config Version Wrong (%X)\n",
+				factory_config.version);
+		return;
+	}
+
+	pr_info("MityOMAPL138: Found MAC = %pM\n", factory_config.mac);
+	pr_info("MityOMAPL138: Part Number = %s\n", factory_config.partnum);
+	if (is_valid_ether_addr(factory_config.mac))
+		memcpy(soc_info->emac_pdata->mac_addr,
+			factory_config.mac, ETH_ALEN);
+	else
+		pr_warning("MityOMAPL138: Invalid MAC found "
+				"in factory config block\n");
+}
+
+static struct at24_platform_data mityomapl138_fd_chip = {
+	.byte_len	= 256,
+	.page_size	= 8,
+	.flags		= AT24_FLAG_READONLY | AT24_FLAG_IRUGO,
+	.setup		= read_factory_config,
+	.context	= NULL,
+};
+
+static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = {
+	.bus_freq	= 100,	/* kHz */
+	.bus_delay	= 0,	/* usec */
+};
+
+/* TPS65023 voltage regulator support */
+/* 1.2V Core */
+static struct regulator_consumer_supply tps65023_dcdc1_consumers[] = {
+	{
+		.supply = "cvdd",
+	},
+};
+
+/* 1.8V */
+static struct regulator_consumer_supply tps65023_dcdc2_consumers[] = {
+	{
+		.supply = "usb0_vdda18",
+	},
+	{
+		.supply = "usb1_vdda18",
+	},
+	{
+		.supply = "ddr_dvdd18",
+	},
+	{
+		.supply = "sata_vddr",
+	},
+};
+
+/* 1.2V */
+static struct regulator_consumer_supply tps65023_dcdc3_consumers[] = {
+	{
+		.supply = "sata_vdd",
+	},
+	{
+		.supply = "usb_cvdd",
+	},
+	{
+		.supply = "pll0_vdda",
+	},
+	{
+		.supply = "pll1_vdda",
+	},
+};
+
+/* 1.8V Aux LDO, not used */
+static struct regulator_consumer_supply tps65023_ldo1_consumers[] = {
+	{
+		.supply = "1.8v_aux",
+	},
+};
+
+/* FPGA VCC Aux (2.5 or 3.3) LDO */
+static struct regulator_consumer_supply tps65023_ldo2_consumers[] = {
+	{
+		.supply = "vccaux",
+	},
+};
+
+static struct regulator_init_data tps65023_regulator_data[] = {
+	/* dcdc1 */
+	{
+		.constraints = {
+			.min_uV = 1150000,
+			.max_uV = 1350000,
+			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+					  REGULATOR_CHANGE_STATUS,
+			.boot_on = 1,
+		},
+		.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers),
+		.consumer_supplies = tps65023_dcdc1_consumers,
+	},
+	/* dcdc2 */
+	{
+		.constraints = {
+			.min_uV = 1800000,
+			.max_uV = 1800000,
+			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+			.boot_on = 1,
+		},
+		.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers),
+		.consumer_supplies = tps65023_dcdc2_consumers,
+	},
+	/* dcdc3 */
+	{
+		.constraints = {
+			.min_uV = 1200000,
+			.max_uV = 1200000,
+			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+			.boot_on = 1,
+		},
+		.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers),
+		.consumer_supplies = tps65023_dcdc3_consumers,
+	},
+	/* ldo1 */
+	{
+		.constraints = {
+			.min_uV = 1800000,
+			.max_uV = 1800000,
+			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+			.boot_on = 1,
+		},
+		.num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers),
+		.consumer_supplies = tps65023_ldo1_consumers,
+	},
+	/* ldo2 */
+	{
+		.constraints = {
+			.min_uV = 2500000,
+			.max_uV = 3300000,
+			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+					  REGULATOR_CHANGE_STATUS,
+			.boot_on = 1,
+		},
+		.num_consumer_supplies = ARRAY_SIZE(tps65023_ldo2_consumers),
+		.consumer_supplies = tps65023_ldo2_consumers,
+	},
+};
+
+static struct i2c_board_info __initdata mityomap_tps65023_info[] = {
+	{
+		I2C_BOARD_INFO("tps65023", 0x48),
+		.platform_data = &tps65023_regulator_data[0],
+	},
+	{
+		I2C_BOARD_INFO("24c02", 0x50),
+		.platform_data = &mityomapl138_fd_chip,
+	},
+};
+
+static int __init pmic_tps65023_init(void)
+{
+	return i2c_register_board_info(1, mityomap_tps65023_info,
+					ARRAY_SIZE(mityomap_tps65023_info));
+}
+
+/*
+ * MityDSP-L138 includes a 256 MByte large-page NAND flash
+ * (128K blocks).
+ */
+static struct mtd_partition mityomapl138_nandflash_partition[] = {
+	{
+		.name		= "rootfs",
+		.offset		= 0,
+		.size		= SZ_128M,
+		.mask_flags	= 0, /* MTD_WRITEABLE, */
+	},
+	{
+		.name		= "homefs",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= 0,
+	},
+};
+
+static struct davinci_nand_pdata mityomapl138_nandflash_data = {
+	.parts		= mityomapl138_nandflash_partition,
+	.nr_parts	= ARRAY_SIZE(mityomapl138_nandflash_partition),
+	.ecc_mode	= NAND_ECC_HW,
+	.options	= NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
+	.ecc_bits	= 1, /* 4 bit mode is not supported with 16 bit NAND */
+};
+
+static struct resource mityomapl138_nandflash_resource[] = {
+	{
+		.start	= DA8XX_AEMIF_CS3_BASE,
+		.end	= DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= DA8XX_AEMIF_CTL_BASE,
+		.end	= DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device mityomapl138_nandflash_device = {
+	.name		= "davinci_nand",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &mityomapl138_nandflash_data,
+	},
+	.num_resources	= ARRAY_SIZE(mityomapl138_nandflash_resource),
+	.resource	= mityomapl138_nandflash_resource,
+};
+
+static struct platform_device *mityomapl138_devices[] __initdata = {
+	&mityomapl138_nandflash_device,
+};
+
+static void __init mityomapl138_setup_nand(void)
+{
+	platform_add_devices(mityomapl138_devices,
+				 ARRAY_SIZE(mityomapl138_devices));
+}
+
+static struct davinci_uart_config mityomapl138_uart_config __initdata = {
+	.enabled_uarts = 0x7,
+};
+
+static const short mityomap_mii_pins[] = {
+	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
+	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
+	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
+	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
+	DA850_MDIO_D,
+	-1
+};
+
+static const short mityomap_rmii_pins[] = {
+	DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
+	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
+	DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
+	DA850_MDIO_D,
+	-1
+};
+
+static void __init mityomapl138_config_emac(void)
+{
+	void __iomem *cfg_chip3_base;
+	int ret;
+	u32 val;
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */
+
+	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
+	val = __raw_readl(cfg_chip3_base);
+
+	if (soc_info->emac_pdata->rmii_en) {
+		val |= BIT(8);
+		ret = davinci_cfg_reg_list(mityomap_rmii_pins);
+		pr_info("RMII PHY configured\n");
+	} else {
+		val &= ~BIT(8);
+		ret = davinci_cfg_reg_list(mityomap_mii_pins);
+		pr_info("MII PHY configured\n");
+	}
+
+	if (ret) {
+		pr_warning("mii/rmii mux setup failed: %d\n", ret);
+		return;
+	}
+
+	/* configure the CFGCHIP3 register for RMII or MII */
+	__raw_writel(val, cfg_chip3_base);
+
+	soc_info->emac_pdata->phy_id = MITYOMAPL138_PHY_ID;
+
+	ret = da8xx_register_emac();
+	if (ret)
+		pr_warning("emac registration failed: %d\n", ret);
+}
+
+static struct davinci_pm_config da850_pm_pdata = {
+	.sleepcount = 128,
+};
+
+static struct platform_device da850_pm_device = {
+	.name	= "pm-davinci",
+	.dev = {
+		.platform_data  = &da850_pm_pdata,
+	},
+	.id	= -1,
+};
+
+static void __init mityomapl138_init(void)
+{
+	int ret;
+
+	/* for now, no special EDMA channels are reserved */
+	ret = da850_register_edma(NULL);
+	if (ret)
+		pr_warning("edma registration failed: %d\n", ret);
+
+	ret = da8xx_register_watchdog();
+	if (ret)
+		pr_warning("watchdog registration failed: %d\n", ret);
+
+	davinci_serial_init(&mityomapl138_uart_config);
+
+	ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata);
+	if (ret)
+		pr_warning("i2c0 registration failed: %d\n", ret);
+
+	ret = pmic_tps65023_init();
+	if (ret)
+		pr_warning("TPS65023 PMIC init failed: %d\n", ret);
+
+	mityomapl138_setup_nand();
+
+	mityomapl138_config_emac();
+
+	ret = da8xx_register_rtc();
+	if (ret)
+		pr_warning("rtc setup failed: %d\n", ret);
+
+	ret = da850_register_cpufreq("pll0_sysclk3");
+	if (ret)
+		pr_warning("cpufreq registration failed: %d\n", ret);
+
+	ret = da8xx_register_cpuidle();
+	if (ret)
+		pr_warning("cpuidle registration failed: %d\n", ret);
+
+	ret = da850_register_pm(&da850_pm_device);
+	if (ret)
+		pr_warning("da850_evm_init: suspend registration failed: %d\n",
+				ret);
+}
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init mityomapl138_console_init(void)
+{
+	if (!machine_is_mityomapl138())
+		return 0;
+
+	return add_preferred_console("ttyS", 1, "115200");
+}
+console_initcall(mityomapl138_console_init);
+#endif
+
+static void __init mityomapl138_map_io(void)
+{
+	da850_init();
+}
+
+MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
+	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.map_io		= mityomapl138_map_io,
+	.init_irq	= cp_intc_init,
+	.timer		= &davinci_timer,
+	.init_machine	= mityomapl138_init,
+MACHINE_END

arch/arm/mach-davinci/board-neuros-osd2.c

@@ -39,9 +39,7 @@
 #include <mach/mmc.h>
 #include <mach/usb.h>
 
-#define NEUROS_OSD2_PHY_MASK		0x2
-#define NEUROS_OSD2_MDIO_FREQUENCY	2200000 /* PHY bus frequency */
-
+#define NEUROS_OSD2_PHY_ID		"0:01"
 #define LXT971_PHY_ID			0x001378e2
 #define LXT971_PHY_MASK			0xfffffff0
 
@@ -252,8 +250,7 @@ static __init void davinci_ntosd2_init(void)
 	davinci_serial_init(&uart_config);
 	dm644x_init_asp(&dm644x_ntosd2_snd_data);
 
-	soc_info->emac_pdata->phy_mask = NEUROS_OSD2_PHY_MASK;
-	soc_info->emac_pdata->mdio_max_freq = NEUROS_OSD2_MDIO_FREQUENCY;
+	soc_info->emac_pdata->phy_id = NEUROS_OSD2_PHY_ID;
 
 	davinci_setup_usb(1000, 8);
 	/*

arch/arm/mach-davinci/board-omapl138-hawk.c

+/*
+ * Hawkboard.org based on TI's OMAP-L138 Platform
+ *
+ * Initial code: Syed Mohammed Khasim
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of
+ * any kind, whether express or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+
+static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
+	.enabled_uarts = 0x7,
+};
+
+static __init void omapl138_hawk_init(void)
+{
+	int ret;
+
+	davinci_serial_init(&omapl138_hawk_uart_config);
+
+	ret = da8xx_register_watchdog();
+	if (ret)
+		pr_warning("omapl138_hawk_init: "
+			"watchdog registration failed: %d\n",
+			ret);
+}
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init omapl138_hawk_console_init(void)
+{
+	if (!machine_is_omapl138_hawkboard())
+		return 0;
+
+	return add_preferred_console("ttyS", 2, "115200");
+}
+console_initcall(omapl138_hawk_console_init);
+#endif
+
+static void __init omapl138_hawk_map_io(void)
+{
+	da850_init();
+}
+
+MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
+	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.map_io		= omapl138_hawk_map_io,
+	.init_irq	= cp_intc_init,
+	.timer		= &davinci_timer,
+	.init_machine	= omapl138_hawk_init,
+MACHINE_END

arch/arm/mach-davinci/board-sffsdr.c

@@ -42,9 +42,7 @@
 #include <mach/mux.h>
 #include <mach/usb.h>
 
-#define SFFSDR_PHY_MASK		(0x2)
-#define SFFSDR_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-
+#define SFFSDR_PHY_ID		"0:01"
 static struct mtd_partition davinci_sffsdr_nandflash_partition[] = {
 	/* U-Boot Environment: Block 0
 	 * UBL:                Block 1
@@ -143,8 +141,7 @@ static __init void davinci_sffsdr_init(void)
 			     ARRAY_SIZE(davinci_sffsdr_devices));
 	sffsdr_init_i2c();
 	davinci_serial_init(&uart_config);
-	soc_info->emac_pdata->phy_mask = SFFSDR_PHY_MASK;
-	soc_info->emac_pdata->mdio_max_freq = SFFSDR_MDIO_FREQUENCY;
+	soc_info->emac_pdata->phy_id = SFFSDR_PHY_ID;
 	davinci_setup_usb(0, 0); /* We support only peripheral mode. */
 
 	/* mux VLYNQ pins */

arch/arm/mach-davinci/board-tnetv107x-evm.c

@@ -23,6 +23,9 @@
 #include <linux/ratelimit.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/input.h>
+#include <linux/input/matrix_keypad.h>
+
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
@@ -141,10 +144,63 @@ static struct davinci_uart_config serial_config __initconst = {
 	.enabled_uarts	= BIT(1),
 };
 
+static const uint32_t keymap[] = {
+	KEY(0, 0, KEY_NUMERIC_1),
+	KEY(0, 1, KEY_NUMERIC_2),
+	KEY(0, 2, KEY_NUMERIC_3),
+	KEY(0, 3, KEY_FN_F1),
+	KEY(0, 4, KEY_MENU),
+
+	KEY(1, 0, KEY_NUMERIC_4),
+	KEY(1, 1, KEY_NUMERIC_5),
+	KEY(1, 2, KEY_NUMERIC_6),
+	KEY(1, 3, KEY_UP),
+	KEY(1, 4, KEY_FN_F2),
+
+	KEY(2, 0, KEY_NUMERIC_7),
+	KEY(2, 1, KEY_NUMERIC_8),
+	KEY(2, 2, KEY_NUMERIC_9),
+	KEY(2, 3, KEY_LEFT),
+	KEY(2, 4, KEY_ENTER),
+
+	KEY(3, 0, KEY_NUMERIC_STAR),
+	KEY(3, 1, KEY_NUMERIC_0),
+	KEY(3, 2, KEY_NUMERIC_POUND),
+	KEY(3, 3, KEY_DOWN),
+	KEY(3, 4, KEY_RIGHT),
+
+	KEY(4, 0, KEY_FN_F3),
+	KEY(4, 1, KEY_FN_F4),
+	KEY(4, 2, KEY_MUTE),
+	KEY(4, 3, KEY_HOME),
+	KEY(4, 4, KEY_BACK),
+
+	KEY(5, 0, KEY_VOLUMEDOWN),
+	KEY(5, 1, KEY_VOLUMEUP),
+	KEY(5, 2, KEY_F1),
+	KEY(5, 3, KEY_F2),
+	KEY(5, 4, KEY_F3),
+};
+
+static const struct matrix_keymap_data keymap_data = {
+	.keymap		= keymap,
+	.keymap_size	= ARRAY_SIZE(keymap),
+};
+
+static struct matrix_keypad_platform_data keypad_config = {
+	.keymap_data	= &keymap_data,
+	.num_row_gpios	= 6,
+	.num_col_gpios	= 5,
+	.debounce_ms	= 0, /* minimum */
+	.active_low	= 0, /* pull up realization */
+	.no_autorepeat	= 0,
+};
+
 static struct tnetv107x_device_info evm_device_info __initconst = {
 	.serial_config		= &serial_config,
 	.mmc_config[1]		= &mmc_config,	/* controller 1 */
 	.nand_config[0]		= &nand_config,	/* chip select 0 */
+	.keypad_config		= &keypad_config,
 };
 
 static __init void tnetv107x_evm_board_init(void)

arch/arm/mach-davinci/clock.c

@@ -236,7 +236,7 @@ static int __init clk_disable_unused(void)
 		if (!davinci_psc_is_clk_active(ck->gpsc, ck->lpsc))
 			continue;
 
-		pr_info("Clocks: disable unused %s\n", ck->name);
+		pr_debug("Clocks: disable unused %s\n", ck->name);
 
 		davinci_psc_config(psc_domain(ck), ck->gpsc, ck->lpsc,
 				(ck->flags & PSC_SWRSTDISABLE) ?
@@ -287,6 +287,79 @@ static unsigned long clk_sysclk_recalc(struct clk *clk)
 	return rate;
 }
 
+int davinci_set_sysclk_rate(struct clk *clk, unsigned long rate)
+{
+	unsigned v;
+	struct pll_data *pll;
+	unsigned long input;
+	unsigned ratio = 0;
+
+	/* If this is the PLL base clock, wrong function to call */
+	if (clk->pll_data)
+		return -EINVAL;
+
+	/* There must be a parent... */
+	if (WARN_ON(!clk->parent))
+		return -EINVAL;
+
+	/* ... the parent must be a PLL... */
+	if (WARN_ON(!clk->parent->pll_data))
+		return -EINVAL;
+
+	/* ... and this clock must have a divider. */
+	if (WARN_ON(!clk->div_reg))
+		return -EINVAL;
+
+	pll = clk->parent->pll_data;
+
+	input = clk->parent->rate;
+
+	/* If pre-PLL, source clock is before the multiplier and divider(s) */
+	if (clk->flags & PRE_PLL)
+		input = pll->input_rate;
+
+	if (input > rate) {
+		/*
+		 * Can afford to provide an output little higher than requested
+		 * only if maximum rate supported by hardware on this sysclk
+		 * is known.
+		 */
+		if (clk->maxrate) {
+			ratio = DIV_ROUND_CLOSEST(input, rate);
+			if (input / ratio > clk->maxrate)
+				ratio = 0;
+		}
+
+		if (ratio == 0)
+			ratio = DIV_ROUND_UP(input, rate);
+
+		ratio--;
+	}
+
+	if (ratio > PLLDIV_RATIO_MASK)
+		return -EINVAL;
+
+	do {
+		v = __raw_readl(pll->base + PLLSTAT);
+	} while (v & PLLSTAT_GOSTAT);
+
+	v = __raw_readl(pll->base + clk->div_reg);
+	v &= ~PLLDIV_RATIO_MASK;
+	v |= ratio | PLLDIV_EN;
+	__raw_writel(v, pll->base + clk->div_reg);
+
+	v = __raw_readl(pll->base + PLLCMD);
+	v |= PLLCMD_GOSET;
+	__raw_writel(v, pll->base + PLLCMD);
+
+	do {
+		v = __raw_readl(pll->base + PLLSTAT);
+	} while (v & PLLSTAT_GOSTAT);
+
+	return 0;
+}
+EXPORT_SYMBOL(davinci_set_sysclk_rate);
+
 static unsigned long clk_leafclk_recalc(struct clk *clk)
 {
 	if (WARN_ON(!clk->parent))

arch/arm/mach-davinci/clock.h

@@ -70,6 +70,9 @@
 #include <linux/list.h>
 #include <asm/clkdev.h>
 
+#define PLLSTAT_GOSTAT	BIT(0)
+#define PLLCMD_GOSET	BIT(0)
+
 struct pll_data {
 	u32 phys_base;
 	void __iomem *base;
@@ -86,6 +89,7 @@ struct clk {
 	struct module		*owner;
 	const char		*name;
 	unsigned long		rate;
+	unsigned long		maxrate;	/* H/W supported max rate */
 	u8			usecount;
 	u8			lpsc;
 	u8			gpsc;
@@ -118,6 +122,7 @@ struct clk {
 int davinci_clk_init(struct clk_lookup *clocks);
 int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv,
 				unsigned int mult, unsigned int postdiv);
+int davinci_set_sysclk_rate(struct clk *clk, unsigned long rate);
 
 extern struct platform_device davinci_wdt_device;
 extern void davinci_watchdog_reset(struct platform_device *);

arch/arm/mach-davinci/cpufreq.c

@@ -34,6 +34,8 @@
 struct davinci_cpufreq {
 	struct device *dev;
 	struct clk *armclk;
+	struct clk *asyncclk;
+	unsigned long asyncrate;
 };
 static struct davinci_cpufreq cpufreq;
 
@@ -104,15 +106,27 @@ static int davinci_target(struct cpufreq_policy *policy,
 	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
 
 	/* if moving to higher frequency, up the voltage beforehand */
-	if (pdata->set_voltage && freqs.new > freqs.old)
-		pdata->set_voltage(idx);
+	if (pdata->set_voltage && freqs.new > freqs.old) {
+		ret = pdata->set_voltage(idx);
+		if (ret)
+			goto out;
+	}
 
 	ret = clk_set_rate(armclk, idx);
+	if (ret)
+		goto out;
+
+	if (cpufreq.asyncclk) {
+		ret = clk_set_rate(cpufreq.asyncclk, cpufreq.asyncrate);
+		if (ret)
+			goto out;
+	}
 
 	/* if moving to lower freq, lower the voltage after lowering freq */
 	if (pdata->set_voltage && freqs.new < freqs.old)
 		pdata->set_voltage(idx);
 
+out:
 	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
 
 	return ret;
@@ -185,6 +199,7 @@ static struct cpufreq_driver davinci_driver = {
 static int __init davinci_cpufreq_probe(struct platform_device *pdev)
 {
 	struct davinci_cpufreq_config *pdata = pdev->dev.platform_data;
+	struct clk *asyncclk;
 
 	if (!pdata)
 		return -EINVAL;
@@ -199,6 +214,12 @@ static int __init davinci_cpufreq_probe(struct platform_device *pdev)
 		return PTR_ERR(cpufreq.armclk);
 	}
 
+	asyncclk = clk_get(cpufreq.dev, "async");
+	if (!IS_ERR(asyncclk)) {
+		cpufreq.asyncclk = asyncclk;
+		cpufreq.asyncrate = clk_get_rate(asyncclk);
+	}
+
 	return cpufreq_register_driver(&davinci_driver);
 }
 
@@ -206,6 +227,9 @@ static int __exit davinci_cpufreq_remove(struct platform_device *pdev)
 {
 	clk_put(cpufreq.armclk);
 
+	if (cpufreq.asyncclk)
+		clk_put(cpufreq.asyncclk);
+
 	return cpufreq_unregister_driver(&davinci_driver);
 }
 

arch/arm/mach-davinci/da850.c

@@ -86,6 +86,8 @@ static struct clk pll0_sysclk3 = {
 	.parent		= &pll0_clk,
 	.flags		= CLK_PLL,
 	.div_reg	= PLLDIV3,
+	.set_rate	= davinci_set_sysclk_rate,
+	.maxrate	= 100000000,
 };
 
 static struct clk pll0_sysclk4 = {
@@ -323,12 +325,19 @@ static struct clk lcdc_clk = {
 	.gpsc		= 1,
 };
 
-static struct clk mmcsd_clk = {
-	.name		= "mmcsd",
+static struct clk mmcsd0_clk = {
+	.name		= "mmcsd0",
 	.parent		= &pll0_sysclk2,
 	.lpsc		= DA8XX_LPSC0_MMC_SD,
 };
 
+static struct clk mmcsd1_clk = {
+	.name		= "mmcsd1",
+	.parent		= &pll0_sysclk2,
+	.lpsc		= DA850_LPSC1_MMC_SD1,
+	.gpsc		= 1,
+};
+
 static struct clk aemif_clk = {
 	.name		= "aemif",
 	.parent		= &pll0_sysclk3,
@@ -375,7 +384,8 @@ static struct clk_lookup da850_clks[] = {
 	CLK("davinci_emac.1",	NULL,		&emac_clk),
 	CLK("davinci-mcasp.0",	NULL,		&mcasp_clk),
 	CLK("da8xx_lcdc.0",	NULL,		&lcdc_clk),
-	CLK("davinci_mmc.0",	NULL,		&mmcsd_clk),
+	CLK("davinci_mmc.0",	NULL,		&mmcsd0_clk),
+	CLK("davinci_mmc.1",	NULL,		&mmcsd1_clk),
 	CLK(NULL,		"aemif",	&aemif_clk),
 	CLK(NULL,		NULL,		NULL),
 };
@@ -572,15 +582,9 @@ const short da850_cpgmac_pins[] __initdata = {
 	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
 	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
 	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
-	DA850_MDIO_D,
-	-1
-};
-
-const short da850_rmii_pins[] __initdata = {
-	DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
-	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
-	DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
-	DA850_MDIO_D,
+	DA850_MDIO_D, DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
+	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, DA850_RMII_RXER,
+	DA850_RMII_MHZ_50_CLK,
 	-1
 };
 
@@ -607,27 +611,19 @@ const short da850_mmcsd0_pins[] __initdata = {
 	-1
 };
 
-const short da850_nand_pins[] __initdata = {
-	DA850_EMA_D_7, DA850_EMA_D_6, DA850_EMA_D_5, DA850_EMA_D_4,
-	DA850_EMA_D_3, DA850_EMA_D_2, DA850_EMA_D_1, DA850_EMA_D_0,
-	DA850_EMA_A_1, DA850_EMA_A_2, DA850_NEMA_CS_3, DA850_NEMA_CS_4,
-	DA850_NEMA_WE, DA850_NEMA_OE,
-	-1
-};
-
-const short da850_nor_pins[] __initdata = {
+const short da850_emif25_pins[] __initdata = {
 	DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2,
-	DA850_NEMA_WE, DA850_NEMA_OE, DA850_EMA_D_0, DA850_EMA_D_1,
-	DA850_EMA_D_2, DA850_EMA_D_3, DA850_EMA_D_4, DA850_EMA_D_5,
-	DA850_EMA_D_6, DA850_EMA_D_7, DA850_EMA_D_8, DA850_EMA_D_9,
-	DA850_EMA_D_10, DA850_EMA_D_11, DA850_EMA_D_12, DA850_EMA_D_13,
-	DA850_EMA_D_14, DA850_EMA_D_15, DA850_EMA_A_0, DA850_EMA_A_1,
-	DA850_EMA_A_2, DA850_EMA_A_3, DA850_EMA_A_4, DA850_EMA_A_5,
-	DA850_EMA_A_6, DA850_EMA_A_7, DA850_EMA_A_8, DA850_EMA_A_9,
-	DA850_EMA_A_10, DA850_EMA_A_11, DA850_EMA_A_12, DA850_EMA_A_13,
-	DA850_EMA_A_14, DA850_EMA_A_15, DA850_EMA_A_16, DA850_EMA_A_17,
-	DA850_EMA_A_18, DA850_EMA_A_19, DA850_EMA_A_20, DA850_EMA_A_21,
-	DA850_EMA_A_22, DA850_EMA_A_23,
+	DA850_NEMA_CS_3, DA850_NEMA_CS_4, DA850_NEMA_WE, DA850_NEMA_OE,
+	DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3,
+	DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7,
+	DA850_EMA_D_8, DA850_EMA_D_9, DA850_EMA_D_10, DA850_EMA_D_11,
+	DA850_EMA_D_12, DA850_EMA_D_13, DA850_EMA_D_14, DA850_EMA_D_15,
+	DA850_EMA_A_0, DA850_EMA_A_1, DA850_EMA_A_2, DA850_EMA_A_3,
+	DA850_EMA_A_4, DA850_EMA_A_5, DA850_EMA_A_6, DA850_EMA_A_7,
+	DA850_EMA_A_8, DA850_EMA_A_9, DA850_EMA_A_10, DA850_EMA_A_11,
+	DA850_EMA_A_12, DA850_EMA_A_13, DA850_EMA_A_14, DA850_EMA_A_15,
+	DA850_EMA_A_16, DA850_EMA_A_17, DA850_EMA_A_18, DA850_EMA_A_19,
+	DA850_EMA_A_20, DA850_EMA_A_21, DA850_EMA_A_22, DA850_EMA_A_23,
 	-1
 };
 
@@ -851,7 +847,7 @@ static const struct da850_opp da850_opp_300 = {
 	.prediv		= 1,
 	.mult		= 25,
 	.postdiv	= 2,
-	.cvdd_min	= 1140000,
+	.cvdd_min	= 1200000,
 	.cvdd_max	= 1320000,
 };
 
@@ -860,7 +856,7 @@ static const struct da850_opp da850_opp_200 = {
 	.prediv		= 1,
 	.mult		= 25,
 	.postdiv	= 3,
-	.cvdd_min	= 1050000,
+	.cvdd_min	= 1100000,
 	.cvdd_max	= 1160000,
 };
 
@@ -869,7 +865,7 @@ static const struct da850_opp da850_opp_96 = {
 	.prediv		= 1,
 	.mult		= 20,
 	.postdiv	= 5,
-	.cvdd_min	= 950000,
+	.cvdd_min	= 1000000,
 	.cvdd_max	= 1050000,
 };
 
@@ -929,10 +925,16 @@ static struct platform_device da850_cpufreq_device = {
 	.dev = {
 		.platform_data	= &cpufreq_info,
 	},
+	.id = -1,
 };
 
-int __init da850_register_cpufreq(void)
+int __init da850_register_cpufreq(char *async_clk)
 {
+	/* cpufreq driver can help keep an "async" clock constant */
+	if (async_clk)
+		clk_add_alias("async", da850_cpufreq_device.name,
+							async_clk, NULL);
+
 	return platform_device_register(&da850_cpufreq_device);
 }
 
@@ -983,7 +985,7 @@ static int da850_set_pll0rate(struct clk *clk, unsigned long index)
 	return 0;
 }
 #else
-int __init da850_register_cpufreq(void)
+int __init da850_register_cpufreq(char *async_clk)
 {
 	return 0;
 }

arch/arm/mach-davinci/devices-da8xx.c

@@ -24,6 +24,7 @@
 #include "clock.h"
 
 #define DA8XX_TPCC_BASE			0x01c00000
+#define DA850_MMCSD1_BASE		0x01e1b000
 #define DA850_TPCC1_BASE		0x01e30000
 #define DA8XX_TPTC0_BASE		0x01c08000
 #define DA8XX_TPTC1_BASE		0x01c08400
@@ -41,7 +42,6 @@
 #define DA8XX_EMAC_CTRL_REG_OFFSET	0x3000
 #define DA8XX_EMAC_MOD_REG_OFFSET	0x2000
 #define DA8XX_EMAC_RAM_OFFSET		0x0000
-#define DA8XX_MDIO_REG_OFFSET		0x4000
 #define DA8XX_EMAC_CTRL_RAM_SIZE	SZ_8K
 
 void __iomem *da8xx_syscfg0_base;
@@ -351,7 +351,7 @@ int __init da8xx_register_watchdog(void)
 static struct resource da8xx_emac_resources[] = {
 	{
 		.start	= DA8XX_EMAC_CPPI_PORT_BASE,
-		.end	= DA8XX_EMAC_CPPI_PORT_BASE + 0x5000 - 1,
+		.end	= DA8XX_EMAC_CPPI_PORT_BASE + SZ_16K - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	{
@@ -380,7 +380,6 @@ struct emac_platform_data da8xx_emac_pdata = {
 	.ctrl_reg_offset	= DA8XX_EMAC_CTRL_REG_OFFSET,
 	.ctrl_mod_reg_offset	= DA8XX_EMAC_MOD_REG_OFFSET,
 	.ctrl_ram_offset	= DA8XX_EMAC_RAM_OFFSET,
-	.mdio_reg_offset	= DA8XX_MDIO_REG_OFFSET,
 	.ctrl_ram_size		= DA8XX_EMAC_CTRL_RAM_SIZE,
 	.version		= EMAC_VERSION_2,
 };
@@ -395,9 +394,34 @@ static struct platform_device da8xx_emac_device = {
 	.resource	= da8xx_emac_resources,
 };
 
+static struct resource da8xx_mdio_resources[] = {
+	{
+		.start	= DA8XX_EMAC_MDIO_BASE,
+		.end	= DA8XX_EMAC_MDIO_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device da8xx_mdio_device = {
+	.name		= "davinci_mdio",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(da8xx_mdio_resources),
+	.resource	= da8xx_mdio_resources,
+};
+
 int __init da8xx_register_emac(void)
 {
-	return platform_device_register(&da8xx_emac_device);
+	int ret;
+
+	ret = platform_device_register(&da8xx_mdio_device);
+	if (ret < 0)
+		return ret;
+	ret = platform_device_register(&da8xx_emac_device);
+	if (ret < 0)
+		return ret;
+	ret = clk_add_alias(NULL, dev_name(&da8xx_mdio_device.dev),
+			    NULL, &da8xx_emac_device.dev);
+	return ret;
 }
 
 static struct resource da830_mcasp1_resources[] = {
@@ -566,6 +590,44 @@ int __init da8xx_register_mmcsd0(struct davinci_mmc_config *config)
 	return platform_device_register(&da8xx_mmcsd0_device);
 }
 
+#ifdef CONFIG_ARCH_DAVINCI_DA850
+static struct resource da850_mmcsd1_resources[] = {
+	{		/* registers */
+		.start	= DA850_MMCSD1_BASE,
+		.end	= DA850_MMCSD1_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{		/* interrupt */
+		.start	= IRQ_DA850_MMCSDINT0_1,
+		.end	= IRQ_DA850_MMCSDINT0_1,
+		.flags	= IORESOURCE_IRQ,
+	},
+	{		/* DMA RX */
+		.start	= EDMA_CTLR_CHAN(1, 28),
+		.end	= EDMA_CTLR_CHAN(1, 28),
+		.flags	= IORESOURCE_DMA,
+	},
+	{		/* DMA TX */
+		.start	= EDMA_CTLR_CHAN(1, 29),
+		.end	= EDMA_CTLR_CHAN(1, 29),
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device da850_mmcsd1_device = {
+	.name		= "davinci_mmc",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(da850_mmcsd1_resources),
+	.resource	= da850_mmcsd1_resources,
+};
+
+int __init da850_register_mmcsd1(struct davinci_mmc_config *config)
+{
+	da850_mmcsd1_device.dev.platform_data = config;
+	return platform_device_register(&da850_mmcsd1_device);
+}
+#endif
+
 static struct resource da8xx_rtc_resources[] = {
 	{
 		.start		= DA8XX_RTC_BASE,