Kconfig

	  <http://www.tldp.org/docs.html#howto>.  If you use this driver,
	  you will still be able to use the parallel port for other tasks,
	  such as a printer; it is safe to compile both drivers into the
	  kernel.

	  To compile this driver as a module, choose M here: the
	  module will be called ppa.

config SCSI_IMM
	tristate "IOMEGA parallel port (imm - newer drives)"
	depends on SCSI && PARPORT_PC
	---help---
	  This driver supports newer versions of IOMEGA's parallel port ZIP
	  drive (a 100 MB removable media device).

	  Note that you can say N here if you have the SCSI version of the ZIP
	  drive: it will be supported automatically if you said Y to the
	  generic "SCSI disk support", above.

	  If you have the ZIP Plus drive or a more recent parallel port ZIP
	  drive (if the supplied cable with the drive is labeled "AutoDetect")
	  then you should say Y here; if you have an older ZIP drive, say N
	  here and Y to "IOMEGA Parallel Port (ppa - older drives)", above.

	  For more information about this driver and how to use it you should
	  read the file <file:Documentation/scsi/ppa.txt>.  You should also read
	  the SCSI-HOWTO, which is available from
	  <http://www.tldp.org/docs.html#howto>.  If you use this driver,
	  you will still be able to use the parallel port for other tasks,
	  such as a printer; it is safe to compile both drivers into the
	  kernel.

	  To compile this driver as a module, choose M here: the
	  module will be called imm.

config SCSI_IZIP_EPP16
	bool "ppa/imm option - Use slow (but safe) EPP-16"
	depends on SCSI_PPA || SCSI_IMM
	---help---
	  EPP (Enhanced Parallel Port) is a standard for parallel ports which
	  allows them to act as expansion buses that can handle up to 64
	  peripheral devices.

	  Some parallel port chipsets are slower than their motherboard, and
	  so we have to control the state of the chipset's FIFO queue every
	  now and then to avoid data loss. This will be done if you say Y
	  here.

	  Generally, saying Y is the safe option and slows things down a bit.

config SCSI_IZIP_SLOW_CTR
	bool "ppa/imm option - Assume slow parport control register"
	depends on SCSI_PPA || SCSI_IMM
	help
	  Some parallel ports are known to have excessive delays between
	  changing the parallel port control register and good data being
	  available on the parallel port data/status register. This option
	  forces a small delay (1.0 usec to be exact) after changing the
	  control register to let things settle out. Enabling this option may
	  result in a big drop in performance but some very old parallel ports
	  (found in 386 vintage machines) will not work properly.

	  Generally, saying N is fine.

config SCSI_NCR53C406A
	tristate "NCR53c406a SCSI support"
	depends on ISA && SCSI
	help
	  This is support for the NCR53c406a SCSI host adapter.  For user
	  configurable parameters, check out <file:drivers/scsi/NCR53c406a.c>
	  in the kernel source.  Also read the SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the
	  module will be called NCR53c406.

config SCSI_NCR_D700
	tristate "NCR Dual 700 MCA SCSI support"
	depends on MCA && SCSI
	select SCSI_SPI_ATTRS
	help
	  This is a driver for the MicroChannel Dual 700 card produced by
	  NCR and commonly used in 345x/35xx/4100 class machines.  It always
	  tries to negotiate sync and uses tag command queueing.

	  Unless you have an NCR manufactured machine, the chances are that
	  you do not have this SCSI card, so say N.

config SCSI_LASI700
	tristate "HP Lasi SCSI support for 53c700/710"
	depends on GSC && SCSI
	select SCSI_SPI_ATTRS
	help
	  This is a driver for the SCSI controller in the Lasi chip found in
	  many PA-RISC workstations & servers.  If you do not know whether you
	  have a Lasi chip, it is safe to say "Y" here.

config SCSI_SNI_53C710
	tristate "SNI RM SCSI support for 53c710"
	depends on SNI_RM && SCSI
	select SCSI_SPI_ATTRS
	select 53C700_LE_ON_BE
	help
	  This is a driver for the onboard SCSI controller found in older
	  SNI RM workstations & servers.

config 53C700_LE_ON_BE
	bool
	depends on SCSI_LASI700
	default y

config SCSI_STEX
	tristate "Promise SuperTrak EX Series support"
	depends on PCI && SCSI
	---help---
	  This driver supports Promise SuperTrak EX series storage controllers.

	  Promise provides Linux RAID configuration utility for these
	  controllers. Please visit <http://www.promise.com> to download.

	  To compile this driver as a module, choose M here: the
	  module will be called stex.

config 53C700_BE_BUS
	bool
	depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI
	default y

config SCSI_SYM53C8XX_2
	tristate "SYM53C8XX Version 2 SCSI support"
	depends on PCI && SCSI
	select SCSI_SPI_ATTRS
	---help---
	  This driver supports the whole NCR53C8XX/SYM53C8XX family of
	  PCI-SCSI controllers.  It also supports the subset of LSI53C10XX
	  Ultra-160 controllers that are based on the SYM53C8XX SCRIPTS
	  language.  It does not support LSI53C10XX Ultra-320 PCI-X SCSI
	  controllers; you need to use the Fusion MPT driver for that.

	  Please read <file:Documentation/scsi/sym53c8xx_2.txt> for more
	  information.

config SCSI_SYM53C8XX_DMA_ADDRESSING_MODE
	int "DMA addressing mode"
	depends on SCSI_SYM53C8XX_2
	default "1"
	---help---
	  This option only applies to PCI-SCSI chips that are PCI DAC
	  capable (875A, 895A, 896, 1010-33, 1010-66, 1000).

	  When set to 0, the driver will program the chip to only perform
	  32-bit DMA.  When set to 1, the chip will be able to perform DMA
	  to addresses up to 1TB.  When set to 2, the driver supports the
	  full 64-bit DMA address range, but can only address 16 segments
	  of 4 GB each.  This limits the total addressable range to 64 GB.

	  Most machines with less than 4GB of memory should use a setting
	  of 0 for best performance.  If your machine has 4GB of memory
	  or more, you should set this option to 1 (the default).

	  The still experimental value 2 (64 bit DMA addressing with 16
	  x 4GB segments limitation) can be used on systems that require
	  PCI address bits past bit 39 to be set for the addressing of
	  memory using PCI DAC cycles.

config SCSI_SYM53C8XX_DEFAULT_TAGS
	int "Default tagged command queue depth"
	depends on SCSI_SYM53C8XX_2
	default "16"
	help
	  This is the default value of the command queue depth the
	  driver will announce to the generic SCSI layer for devices
	  that support tagged command queueing. This value can be changed
	  from the boot command line.  This is a soft limit that cannot
	  exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.

config SCSI_SYM53C8XX_MAX_TAGS
	int "Maximum number of queued commands"
	depends on SCSI_SYM53C8XX_2
	default "64"
	help
	  This option allows you to specify the maximum number of commands
	  that can be queued to any device, when tagged command queuing is
	  possible. The driver supports up to 256 queued commands per device.
	  This value is used as a compiled-in hard limit.

config SCSI_SYM53C8XX_MMIO
	bool "Use memory mapped IO"
	depends on SCSI_SYM53C8XX_2
	default y
	help
	  Memory mapped IO is faster than Port IO.  Most people should
	  answer Y here, but some machines may have problems.  If you have
	  to answer N here, please report the problem to the maintainer.

config SCSI_IPR
	tristate "IBM Power Linux RAID adapter support"
	depends on PCI && SCSI && ATA
	select FW_LOADER
	---help---
	  This driver supports the IBM Power Linux family RAID adapters.
	  This includes IBM pSeries 5712, 5703, 5709, and 570A, as well
	  as IBM iSeries 5702, 5703, 5709, and 570A.

config SCSI_IPR_TRACE
	bool "enable driver internal trace"
	depends on SCSI_IPR
	default y
	help
	  If you say Y here, the driver will trace all commands issued
	  to the adapter. Performance impact is minimal. Trace can be
	  dumped using /sys/bus/class/scsi_host/hostXX/trace.

config SCSI_IPR_DUMP
	bool "enable adapter dump support"
	depends on SCSI_IPR
	default y
	help
	  If you say Y here, the driver will support adapter crash dump.
	  If you enable this support, the iprdump daemon can be used
	  to capture adapter failure analysis information.

config SCSI_ZALON
	tristate "Zalon SCSI support"
	depends on GSC && SCSI
	select SCSI_SPI_ATTRS
	help
	  The Zalon is a GSC/HSC bus interface chip that sits between the
	  PA-RISC processor and the NCR 53c720 SCSI controller on C100,
	  C110, J200, J210 and some D, K & R-class machines.  It's also
	  used on the add-in Bluefish, Barracuda & Shrike SCSI cards.
	  Say Y here if you have one of these machines or cards.

config SCSI_NCR_Q720
	tristate "NCR Quad 720 MCA SCSI support"
	depends on MCA && SCSI
	select SCSI_SPI_ATTRS
	help
	  This is a driver for the MicroChannel Quad 720 card produced by
	  NCR and commonly used in 345x/35xx/4100 class machines.  It always
	  tries to negotiate sync and uses tag command queueing.

	  Unless you have an NCR manufactured machine, the chances are that
	  you do not have this SCSI card, so say N.

config SCSI_NCR53C8XX_DEFAULT_TAGS
	int "default tagged command queue depth"
	depends on SCSI_ZALON || SCSI_NCR_Q720
	default "8"
	---help---
	  "Tagged command queuing" is a feature of SCSI-2 which improves
	  performance: the host adapter can send several SCSI commands to a
	  device's queue even if previous commands haven't finished yet.
	  Because the device is intelligent, it can optimize its operations
	  (like head positioning) based on its own request queue. Some SCSI
	  devices don't implement this properly; if you want to disable this
	  feature, enter 0 or 1 here (it doesn't matter which).

	  The default value is 8 and should be supported by most hard disks.
	  This value can be overridden from the boot command line using the
	  'tags' option as follows (example):
	  'ncr53c8xx=tags:4/t2t3q16/t0u2q10' will set default queue depth to
	  4, set queue depth to 16 for target 2 and target 3 on controller 0
	  and set queue depth to 10 for target 0 / lun 2 on controller 1.

	  The normal answer therefore is to go with the default 8 and to use
	  a boot command line option for devices that need to use a different
	  command queue depth.

	  There is no safe option other than using good SCSI devices.

config SCSI_NCR53C8XX_MAX_TAGS
	int "maximum number of queued commands"
	depends on SCSI_ZALON || SCSI_NCR_Q720
	default "32"
	---help---
	  This option allows you to specify the maximum number of commands
	  that can be queued to any device, when tagged command queuing is
	  possible. The default value is 32. Minimum is 2, maximum is 64.
	  Modern hard disks are able to support 64 tags and even more, but
	  do not seem to be faster when more than 32 tags are being used.

	  So, the normal answer here is to go with the default value 32 unless
	  you are using very large hard disks with large cache (>= 1 MB) that
	  are able to take advantage of more than 32 tagged commands.

	  There is no safe option and the default answer is recommended.

config SCSI_NCR53C8XX_SYNC
	int "synchronous transfers frequency in MHz"
	depends on SCSI_ZALON || SCSI_NCR_Q720
	default "20"
	---help---
	  The SCSI Parallel Interface-2 Standard defines 5 classes of transfer
	  rates: FAST-5, FAST-10, FAST-20, FAST-40 and FAST-80.  The numbers
	  are respectively the maximum data transfer rates in mega-transfers
	  per second for each class.  For example, a FAST-20 Wide 16 device is
	  able to transfer data at 20 million 16 bit packets per second for a
	  total rate of 40 MB/s.

	  You may specify 0 if you want to only use asynchronous data
	  transfers. This is the safest and slowest option. Otherwise, specify
	  a value between 5 and 80, depending on the capability of your SCSI
	  controller.  The higher the number, the faster the data transfer.
	  Note that 80 should normally be ok since the driver decreases the
	  value automatically according to the controller's capabilities.

	  Your answer to this question is ignored for controllers with NVRAM,
	  since the driver will get this information from the user set-up.  It
	  also can be overridden using a boot setup option, as follows
	  (example): 'ncr53c8xx=sync:12' will allow the driver to negotiate
	  for FAST-20 synchronous data transfer (20 mega-transfers per
	  second).

	  The normal answer therefore is not to go with the default but to
	  select the maximum value 80 allowing the driver to use the maximum
	  value supported by each controller. If this causes problems with
	  your SCSI devices, you should come back and decrease the value.

	  There is no safe option other than using good cabling, right
	  terminations and SCSI conformant devices.

config SCSI_NCR53C8XX_NO_DISCONNECT
	bool "not allow targets to disconnect"
	depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
	help
	  This option is only provided for safety if you suspect some SCSI
	  device of yours to not support properly the target-disconnect
	  feature. In that case, you would say Y here. In general however, to
	  not allow targets to disconnect is not reasonable if there is more
	  than 1 device on a SCSI bus. The normal answer therefore is N.

config SCSI_PAS16
	tristate "PAS16 SCSI support"
	depends on ISA && SCSI
	select SCSI_SPI_ATTRS
	---help---
	  This is support for a SCSI host adapter.  It is explained in section
	  3.10 of the SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
	  of the box, you may have to change some settings in
	  <file:drivers/scsi/pas16.h>.

	  To compile this driver as a module, choose M here: the
	  module will be called pas16.

config SCSI_QLOGIC_FAS
	tristate "Qlogic FAS SCSI support"
	depends on ISA && SCSI
	---help---
	  This is a driver for the ISA, VLB, and PCMCIA versions of the Qlogic
	  FastSCSI! cards as well as any other card based on the FASXX chip
	  (including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards).

	  This driver does NOT support the PCI versions of these cards. The
	  PCI versions are supported by the Qlogic ISP driver ("Qlogic ISP
	  SCSI support"), below.

	  Information about this driver is contained in
	  <file:Documentation/scsi/qlogicfas.txt>.  You should also read the
	  SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the
	  module will be called qlogicfas.

config SCSI_QLOGIC_1280
	tristate "Qlogic QLA 1240/1x80/1x160 SCSI support"
	depends on PCI && SCSI
	help
	  Say Y if you have a QLogic ISP1240/1x80/1x160 SCSI host adapter.

	  To compile this driver as a module, choose M here: the
	  module will be called qla1280.

config SCSI_QLOGICPTI
	tristate "PTI Qlogic, ISP Driver"
	depends on SBUS && SCSI
	help
	  This driver supports SBUS SCSI controllers from PTI or QLogic. These
	  controllers are known under Solaris as qpti and in the openprom as
	  PTI,ptisp or QLGC,isp. Note that PCI QLogic SCSI controllers are
	  driven by a different driver.

	  To compile this driver as a module, choose M here: the
	  module will be called qlogicpti.

source "drivers/scsi/qla2xxx/Kconfig"
source "drivers/scsi/qla4xxx/Kconfig"

config SCSI_LPFC
	tristate "Emulex LightPulse Fibre Channel Support"
	depends on PCI && SCSI
	select SCSI_FC_ATTRS
	help
          This lpfc driver supports the Emulex LightPulse
          Family of Fibre Channel PCI host adapters.

config SCSI_LPFC_DEBUG_FS
	bool "Emulex LightPulse Fibre Channel debugfs Support"
	depends on SCSI_LPFC && DEBUG_FS
	help
	  This makes debugging information from the lpfc driver
	  available via the debugfs filesystem.

config SCSI_SIM710
	tristate "Simple 53c710 SCSI support (Compaq, NCR machines)"
	depends on (EISA || MCA) && SCSI
	select SCSI_SPI_ATTRS
	---help---
	  This driver is for NCR53c710 based SCSI host adapters.

	  It currently supports Compaq EISA cards and NCR MCA cards

config SCSI_SYM53C416
	tristate "Symbios 53c416 SCSI support"
	depends on ISA && SCSI
	---help---
	  This is support for the sym53c416 SCSI host adapter, the SCSI
	  adapter that comes with some HP scanners. This driver requires that
	  the sym53c416 is configured first using some sort of PnP
	  configuration program (e.g. isapnp) or by a PnP aware BIOS. If you
	  are using isapnp then you need to compile this driver as a module
	  and then load it using insmod after isapnp has run. The parameters
	  of the configured card(s) should be passed to the driver. The format
	  is:

	  insmod sym53c416 sym53c416=<base>,<irq> [sym53c416_1=<base>,<irq>]

	  To compile this driver as a module, choose M here: the
	  module will be called sym53c416.

config SCSI_DC395x
	tristate "Tekram DC395(U/UW/F) and DC315(U) SCSI support (EXPERIMENTAL)"
	depends on PCI && SCSI && EXPERIMENTAL
	---help---
	  This driver supports PCI SCSI host adapters based on the ASIC
	  TRM-S1040 chip, e.g Tekram DC395(U/UW/F) and DC315(U) variants.

	  This driver works, but is still in experimental status. So better
	  have a bootable disk and a backup in case of emergency.

	  Documentation can be found in <file:Documentation/scsi/dc395x.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called dc395x.

config SCSI_DC390T
	tristate "Tekram DC390(T) and Am53/79C974 SCSI support"
	depends on PCI && SCSI
	---help---
	  This driver supports PCI SCSI host adapters based on the Am53C974A
	  chip, e.g. Tekram DC390(T), DawiControl 2974 and some onboard
	  PCscsi/PCnet (Am53/79C974) solutions.

	  Documentation can be found in <file:Documentation/scsi/tmscsim.txt>.

	  Note that this driver does NOT support Tekram DC390W/U/F, which are
	  based on NCR/Symbios chips. Use "NCR53C8XX SCSI support" for those.

	  To compile this driver as a module, choose M here: the
	  module will be called tmscsim.

config SCSI_T128
	tristate "Trantor T128/T128F/T228 SCSI support"
	depends on ISA && SCSI
	select SCSI_SPI_ATTRS
	select CHECK_SIGNATURE
	---help---
	  This is support for a SCSI host adapter. It is explained in section
	  3.11 of the SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
	  of the box, you may have to change some settings in
	  <file:drivers/scsi/t128.h>.  Note that Trantor was purchased by
	  Adaptec, and some former Trantor products are being sold under the
	  Adaptec name.

	  To compile this driver as a module, choose M here: the
	  module will be called t128.

config SCSI_U14_34F
	tristate "UltraStor 14F/34F support"
	depends on ISA && SCSI && ISA_DMA_API
	---help---
	  This is support for the UltraStor 14F and 34F SCSI-2 host adapters.
	  The source at <file:drivers/scsi/u14-34f.c> contains some
	  information about this hardware.  If the driver doesn't work out of
	  the box, you may have to change some settings in
	  <file: drivers/scsi/u14-34f.c>.  Read the SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  Note that there is also
	  another driver for the same hardware: "UltraStor SCSI support",
	  below.  You should say Y to both only if you want 24F support as
	  well.

	  To compile this driver as a module, choose M here: the
	  module will be called u14-34f.

config SCSI_U14_34F_TAGGED_QUEUE
	bool "enable tagged command queueing"
	depends on SCSI_U14_34F
	help
	  This is a feature of SCSI-2 which improves performance: the host
	  adapter can send several SCSI commands to a device's queue even if
	  previous commands haven't finished yet.
	  This is equivalent to the "u14-34f=tc:y" boot option.

config SCSI_U14_34F_LINKED_COMMANDS
	bool "enable elevator sorting"
	depends on SCSI_U14_34F
	help
	  This option enables elevator sorting for all probed SCSI disks and
	  CD-ROMs. It definitely reduces the average seek distance when doing
	  random seeks, but this does not necessarily result in a noticeable
	  performance improvement: your mileage may vary...
	  This is equivalent to the "u14-34f=lc:y" boot option.

config SCSI_U14_34F_MAX_TAGS
	int "maximum number of queued commands"
	depends on SCSI_U14_34F
	default "8"
	help
	  This specifies how many SCSI commands can be maximally queued for
	  each probed SCSI device. You should reduce the default value of 8
	  only if you have disks with buggy or limited tagged command support.
	  Minimum is 2 and maximum is 14. This value is also the window size
	  used by the elevator sorting option above. The effective value used
	  by the driver for each probed SCSI device is reported at boot time.
	  This is equivalent to the "u14-34f=mq:8" boot option.

config SCSI_ULTRASTOR
	tristate "UltraStor SCSI support"
	depends on X86 && ISA && SCSI
	---help---
	  This is support for the UltraStor 14F, 24F and 34F SCSI-2 host
	  adapter family.  This driver is explained in section 3.12 of the
	  SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
	  of the box, you may have to change some settings in
	  <file:drivers/scsi/ultrastor.h>.

	  Note that there is also another driver for the same hardware:
	  "UltraStor 14F/34F support", above.

	  To compile this driver as a module, choose M here: the
	  module will be called ultrastor.

config SCSI_NSP32
	tristate "Workbit NinjaSCSI-32Bi/UDE support"
	depends on PCI && SCSI && !64BIT
	help
	  This is support for the Workbit NinjaSCSI-32Bi/UDE PCI/Cardbus
	  SCSI host adapter. Please read the SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the
	  module will be called nsp32.

config SCSI_DEBUG
	tristate "SCSI debugging host simulator"
	depends on SCSI
	select CRC_T10DIF
	help
	  This is a host adapter simulator that can simulate multiple hosts
	  each with multiple dummy SCSI devices (disks). It defaults to one
	  host adapter with one dummy SCSI disk. Each dummy disk uses kernel
	  RAM as storage (i.e. it is a ramdisk). To save space when multiple
	  dummy disks are simulated, they share the same kernel RAM for 
	  their storage. See <http://www.torque.net/sg/sdebug.html> for more
	  information. This driver is primarily of use to those testing the
	  SCSI and block subsystems. If unsure, say N.

config SCSI_MESH
	tristate "MESH (Power Mac internal SCSI) support"
	depends on PPC32 && PPC_PMAC && SCSI
	help
	  Many Power Macintoshes and clones have a MESH (Macintosh Enhanced
	  SCSI Hardware) SCSI bus adaptor (the 7200 doesn't, but all of the
	  other Power Macintoshes do). Say Y to include support for this SCSI
	  adaptor.

	  To compile this driver as a module, choose M here: the
	  module will be called mesh.

config SCSI_MESH_SYNC_RATE
	int "maximum synchronous transfer rate (MB/s) (0 = async)"
	depends on SCSI_MESH
	default "5"
	help
	  On Power Macintoshes (and clones) where the MESH SCSI bus adaptor
	  drives a bus which is entirely internal to the machine (such as the
	  7500, 7600, 8500, etc.), the MESH is capable of synchronous
	  operation at up to 10 MB/s. On machines where the SCSI bus
	  controlled by the MESH can have external devices connected, it is
	  usually rated at 5 MB/s. 5 is a safe value here unless you know the
	  MESH SCSI bus is internal only; in that case you can say 10. Say 0
	  to disable synchronous operation.

config SCSI_MESH_RESET_DELAY_MS
	int "initial bus reset delay (ms) (0 = no reset)"
	depends on SCSI_MESH
	default "4000"

config SCSI_MAC53C94
	tristate "53C94 (Power Mac external SCSI) support"
	depends on PPC32 && PPC_PMAC && SCSI
	help
	  On Power Macintoshes (and clones) with two SCSI buses, the external
	  SCSI bus is usually controlled by a 53C94 SCSI bus adaptor. Older
	  machines which only have one SCSI bus, such as the 7200, also use
	  the 53C94. Say Y to include support for the 53C94.

	  To compile this driver as a module, choose M here: the
	  module will be called mac53c94.

source "drivers/scsi/arm/Kconfig"

config JAZZ_ESP
	bool "MIPS JAZZ FAS216 SCSI support"
	depends on MACH_JAZZ && SCSI
	select SCSI_SPI_ATTRS
	help
	  This is the driver for the onboard SCSI host adapter of MIPS Magnum
	  4000, Acer PICA, Olivetti M700-10 and a few other identical OEM
	  systems.

config A3000_SCSI
	tristate "A3000 WD33C93A support"
	depends on AMIGA && SCSI
	help
	  If you have an Amiga 3000 and have SCSI devices connected to the
	  built-in SCSI controller, say Y. Otherwise, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called a3000.

config A2091_SCSI
	tristate "A2091/A590 WD33C93A support"
	depends on ZORRO && SCSI
	help
	  If you have a Commodore A2091 SCSI controller, say Y. Otherwise,
	  say N.

	  To compile this driver as a module, choose M here: the
	  module will be called a2091.

config GVP11_SCSI
	tristate "GVP Series II WD33C93A support"
	depends on ZORRO && SCSI
	---help---
	  If you have a Great Valley Products Series II SCSI controller,
	  answer Y. Also say Y if you have a later model of GVP SCSI
	  controller (such as the GVP A4008 or a Combo board). Otherwise,
	  answer N. This driver does NOT work for the T-Rex series of
	  accelerators from TekMagic and GVP-M.

	  To compile this driver as a module, choose M here: the
	  module will be called gvp11.

config SCSI_A4000T
	tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)"
	depends on AMIGA && SCSI && EXPERIMENTAL
	select SCSI_SPI_ATTRS
	help
	  If you have an Amiga 4000T and have SCSI devices connected to the
	  built-in SCSI controller, say Y. Otherwise, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called a4000t.

config SCSI_ZORRO7XX
	tristate "Zorro NCR53c710 SCSI support (EXPERIMENTAL)"
	depends on ZORRO && SCSI && EXPERIMENTAL
	select SCSI_SPI_ATTRS
	help
	  Support for various NCR53c710-based SCSI controllers on Zorro
	  expansion boards for the Amiga.
	  This includes:
	    - the Amiga 4091 Zorro III SCSI-2 controller,
	    - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller
	      (info at
	      <http://www.lysator.liu.se/amiga/ar/guide/ar310.guide?FEATURE5>),
	    - the SCSI controller on the Phase5 Blizzard PowerUP 603e+
	      accelerator card for the Amiga 1200,
	    - the SCSI controller on the GVP Turbo 040/060 accelerator.

config ATARI_SCSI
	tristate "Atari native SCSI support"
	depends on ATARI && SCSI
	select SCSI_SPI_ATTRS
	select NVRAM
	---help---
	  If you have an Atari with built-in NCR5380 SCSI controller (TT,
	  Falcon, ...) say Y to get it supported. Of course also, if you have
	  a compatible SCSI controller (e.g. for Medusa).

	  To compile this driver as a module, choose M here: the
	  module will be called atari_scsi.

	  This driver supports both styles of NCR integration into the
	  system: the TT style (separate DMA), and the Falcon style (via
	  ST-DMA, replacing ACSI).  It does NOT support other schemes, like
	  in the Hades (without DMA).

config ATARI_SCSI_TOSHIBA_DELAY
	bool "Long delays for Toshiba CD-ROMs"
	depends on ATARI_SCSI
	help
	  This option increases the delay after a SCSI arbitration to
	  accommodate some flaky Toshiba CD-ROM drives. Say Y if you intend to
	  use a Toshiba CD-ROM drive; otherwise, the option is not needed and
	  would impact performance a bit, so say N.

config ATARI_SCSI_RESET_BOOT
	bool "Reset SCSI-devices at boottime"
	depends on ATARI_SCSI
	help
	  Reset the devices on your Atari whenever it boots.  This makes the
	  boot process fractionally longer but may assist recovery from errors
	  that leave the devices with SCSI operations partway completed.

config MAC_SCSI
	bool "Macintosh NCR5380 SCSI"
	depends on MAC && SCSI=y
	select SCSI_SPI_ATTRS
	help
	  This is the NCR 5380 SCSI controller included on most of the 68030
	  based Macintoshes.  If you have one of these say Y and read the
	  SCSI-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

config SCSI_MAC_ESP
	tristate "Macintosh NCR53c9[46] SCSI"
	depends on MAC && SCSI
	select SCSI_SPI_ATTRS
	help
	  This is the NCR 53c9x SCSI controller found on most of the 68040
	  based Macintoshes.

	  To compile this driver as a module, choose M here: the module
	  will be called mac_esp.

config MVME147_SCSI
	bool "WD33C93 SCSI driver for MVME147"
	depends on MVME147 && SCSI=y
	select SCSI_SPI_ATTRS
	help
	  Support for the on-board SCSI controller on the Motorola MVME147
	  single-board computer.

config MVME16x_SCSI
	tristate "NCR53C710 SCSI driver for MVME16x"
	depends on MVME16x && SCSI
	select SCSI_SPI_ATTRS
	help
	  The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
	  SCSI controller chip.  Almost everyone using one of these boards
	  will want to say Y to this question.

config BVME6000_SCSI
	tristate "NCR53C710 SCSI driver for BVME6000"
	depends on BVME6000 && SCSI
	select SCSI_SPI_ATTRS
	help
	  The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
	  SCSI controller chip.  Almost everyone using one of these boards
	  will want to say Y to this question.

config SUN3_SCSI
	tristate "Sun3 NCR5380 SCSI"
	depends on SUN3 && SCSI
	select SCSI_SPI_ATTRS
	help
	  This option will enable support for the OBIO (onboard io) NCR5380
	  SCSI controller found in the Sun 3/50 and 3/60, as well as for
	  "Sun3" type VME scsi controllers also based on the NCR5380.
	  General Linux information on the Sun 3 series (now discontinued)
	  is at <http://www.angelfire.com/ca2/tech68k/sun3.html>.

config SUN3X_ESP
	bool "Sun3x ESP SCSI"
	depends on SUN3X && SCSI=y
	select SCSI_SPI_ATTRS
	help
	  The ESP was an on-board SCSI controller used on Sun 3/80
	  machines.  Say Y here to compile in support for it.

config SCSI_SUNESP
	tristate "Sparc ESP Scsi Driver"
	depends on SBUS && SCSI
	select SCSI_SPI_ATTRS
	help
	  This is the driver for the Sun ESP SCSI host adapter. The ESP
	  chipset is present in most SPARC SBUS-based computers and
	  supports the Emulex family of ESP SCSI chips (esp100, esp100A,
	  esp236, fas101, fas236) as well as the Qlogic fas366 SCSI chip.

	  To compile this driver as a module, choose M here: the
	  module will be called sun_esp.

config ZFCP
	tristate "FCP host bus adapter driver for IBM eServer zSeries"
	depends on S390 && QDIO && SCSI
	select SCSI_FC_ATTRS
	help
          If you want to access SCSI devices attached to your IBM eServer
          zSeries by means of Fibre Channel interfaces say Y.
          For details please refer to the documentation provided by IBM at
          <http://oss.software.ibm.com/developerworks/opensource/linux390>

          This driver is also available as a module. This module will be
          called zfcp. If you want to compile it as a module, say M here
          and read <file:Documentation/kbuild/modules.txt>.

config SCSI_SRP
	tristate "SCSI RDMA Protocol helper library"
	depends on SCSI && PCI
	select SCSI_TGT
	help
	  If you wish to use SRP target drivers, say Y.

	  To compile this driver as a module, choose M here: the
	  module will be called libsrp.

endif # SCSI_LOWLEVEL

source "drivers/scsi/pcmcia/Kconfig"

source "drivers/scsi/device_handler/Kconfig"

source "drivers/scsi/osd/Kconfig"

endmenu