diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt
new file mode 100644
index 0000000000000000000000000000000000000000..93986a5a8018d81296af01c7239945154abcfc8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt
@@ -0,0 +1,30 @@
+* Compact Flash
+
+The Cavium Compact Flash device is connected to the Octeon Boot Bus,
+and is thus a child of the Boot Bus device. It can read and write
+industry standard compact flash devices.
+
+Properties:
+- compatible: "cavium,ebt3000-compact-flash";
+
+ Compatibility with many Cavium evaluation boards.
+
+- reg: The base address of the the CF chip select banks. Depending on
+ the device configuration, there may be one or two banks.
+
+- cavium,bus-width: The width of the connection to the CF devices. Valid
+ values are 8 and 16.
+
+- cavium,true-ide: Optional, if present the CF connection is in True IDE mode.
+
+- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected
+ to this device.
+
+Example:
+ compact-flash@5,0 {
+ compatible = "cavium,ebt3000-compact-flash";
+ reg = <5 0 0x10000>, <6 0 0x10000>;
+ cavium,bus-width = <16>;
+ cavium,true-ide;
+ cavium,dma-engine-handle = <&dma0>;
+ };
diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
new file mode 100644
index 0000000000000000000000000000000000000000..9d6dcd3fe7f996c7d9ca2260ba994345eea19d03
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
@@ -0,0 +1,49 @@
+* General Purpose Input Output (GPIO) bus.
+
+Properties:
+- compatible: "cavium,octeon-3860-gpio"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the GPIO unit's register bank.
+
+- gpio-controller: This is a GPIO controller.
+
+- #gpio-cells: Must be <2>. The first cell is the GPIO pin.
+
+- interrupt-controller: The GPIO controller is also an interrupt
+ controller, many of its pins may be configured as an interrupt
+ source.
+
+- #interrupt-cells: Must be <2>. The first cell is the GPIO pin
+ connected to the interrupt source. The second cell is the interrupt
+ triggering protocol and may have one of four values:
+ 1 - edge triggered on the rising edge.
+ 2 - edge triggered on the falling edge
+ 4 - level triggered active high.
+ 8 - level triggered active low.
+
+- interrupts: Interrupt routing for each pin.
+
+Example:
+
+ gpio-controller@1070000000800 {
+ #gpio-cells = <2>;
+ compatible = "cavium,octeon-3860-gpio";
+ reg = <0x10700 0x00000800 0x0 0x100>;
+ gpio-controller;
+ /* Interrupts are specified by two parts:
+ * 1) GPIO pin number (0..15)
+ * 2) Triggering (1 - edge rising
+ * 2 - edge falling
+ * 4 - level active high
+ * 8 - level active low)
+ */
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ /* The GPIO pin connect to 16 consecutive CUI bits */
+ interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+ <0 20>, <0 21>, <0 22>, <0 23>,
+ <0 24>, <0 25>, <0 26>, <0 27>,
+ <0 28>, <0 29>, <0 30>, <0 31>;
+ };
diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt
new file mode 100644
index 0000000000000000000000000000000000000000..dced82ebe31d49b228bf377482d41ef5b6d03c20
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt
@@ -0,0 +1,34 @@
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>. I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+ twsi0: i2c@1180000001000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cavium,octeon-3860-twsi";
+ reg = <0x11800 0x00001000 0x0 0x200>;
+ interrupts = <0 45>;
+ clock-frequency = <100000>;
+
+ rtc@68 {
+ compatible = "dallas,ds1337";
+ reg = <0x68>;
+ };
+ tmp@4c {
+ compatible = "ti,tmp421";
+ reg = <0x4c>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
new file mode 100644
index 0000000000000000000000000000000000000000..6581478225a230e011375692630dc050e8d8be6b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
@@ -0,0 +1,126 @@
+* Boot Bus
+
+The Octeon Boot Bus is a configurable parallel bus with 8 chip
+selects. Each chip select is independently configurable.
+
+Properties:
+- compatible: "cavium,octeon-3860-bootbus"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the Boot Bus' register bank.
+
+- #address-cells: Must be <2>. The first cell is the chip select
+ within the bootbus. The second cell is the offset from the chip select.
+
+- #size-cells: Must be <1>.
+
+- ranges: There must be one one triplet of (child-bus-address,
+ parent-bus-address, length) for each active chip select. If the
+ length element for any triplet is zero, the chip select is disabled,
+ making it inactive.
+
+The configuration parameters for each chip select are stored in child
+nodes.
+
+Configuration Properties:
+- compatible: "cavium,octeon-3860-bootbus-config"
+
+- cavium,cs-index: A single cell indicating the chip select that
+ corresponds to this configuration.
+
+- cavium,t-adr: A cell specifying the ADR timing (in nS).
+
+- cavium,t-ce: A cell specifying the CE timing (in nS).
+
+- cavium,t-oe: A cell specifying the OE timing (in nS).
+
+- cavium,t-we: A cell specifying the WE timing (in nS).
+
+- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS).
+
+- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS).
+
+- cavium,t-pause: A cell specifying the PAUSE timing (in nS).
+
+- cavium,t-wait: A cell specifying the WAIT timing (in nS).
+
+- cavium,t-page: A cell specifying the PAGE timing (in nS).
+
+- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS).
+
+- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1
+ = 2 bytes, 2 = 4 bytes, 3 = 8 bytes).
+
+- cavium,wait-mode: Optional. If present, wait mode (WAITM) is selected.
+
+- cavium,page-mode: Optional. If present, page mode (PAGEM) is selected.
+
+- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of
+ the bus for this chip select.
+
+- cavium,ale-mode: Optional. If present, ALE mode is selected.
+
+- cavium,sam-mode: Optional. If present, SAM mode is selected.
+
+- cavium,or-mode: Optional. If present, OR mode is selected.
+
+Example:
+ bootbus: bootbus@1180000000000 {
+ compatible = "cavium,octeon-3860-bootbus";
+ reg = <0x11800 0x00000000 0x0 0x200>;
+ /* The chip select number and offset */
+ #address-cells = <2>;
+ /* The size of the chip select region */
+ #size-cells = <1>;
+ ranges = <0 0 0x0 0x1f400000 0xc00000>,
+ <1 0 0x10000 0x30000000 0>,
+ <2 0 0x10000 0x40000000 0>,
+ <3 0 0x10000 0x50000000 0>,
+ <4 0 0x0 0x1d020000 0x10000>,
+ <5 0 0x0 0x1d040000 0x10000>,
+ <6 0 0x0 0x1d050000 0x10000>,
+ <7 0 0x10000 0x90000000 0>;
+
+ cavium,cs-config@0 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <0>;
+ cavium,t-adr = <20>;
+ cavium,t-ce = <60>;
+ cavium,t-oe = <60>;
+ cavium,t-we = <45>;
+ cavium,t-rd-hld = <35>;
+ cavium,t-wr-hld = <45>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <0>;
+ cavium,t-page = <35>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <8>;
+ };
+ .
+ .
+ .
+ cavium,cs-config@6 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <6>;
+ cavium,t-adr = <5>;
+ cavium,t-ce = <300>;
+ cavium,t-oe = <270>;
+ cavium,t-we = <150>;
+ cavium,t-rd-hld = <100>;
+ cavium,t-wr-hld = <70>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <0>;
+ cavium,t-page = <320>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,wait-mode;
+ cavium,bus-width = <16>;
+ };
+ .
+ .
+ .
+ };
diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
new file mode 100644
index 0000000000000000000000000000000000000000..2c2d0746b43d1cf9e86ecc0b5cdd33121b266edf
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
@@ -0,0 +1,26 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-3860-ciu"
+
+ Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs.
+
+- interrupt-controller: This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>. The first cell is the bank within
+ the CIU and may have a value of 0 or 1. The second cell is the bit
+ within the bank and may have a value between 0 and 63.
+
+Example:
+ interrupt-controller@1070000000000 {
+ compatible = "cavium,octeon-3860-ciu";
+ interrupt-controller;
+ /* Interrupts are specified by two parts:
+ * 1) Controller register (0 or 1)
+ * 2) Bit within the register (0..63)
+ */
+ #interrupt-cells = <2>;
+ reg = <0x10700 0x00000000 0x0 0x7000>;
+ };
diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu2.txt b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt
new file mode 100644
index 0000000000000000000000000000000000000000..0ec7ba8bbbcb2bfc55d36acee83003e0ab4285de
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt
@@ -0,0 +1,27 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-6880-ciu2"
+
+ Compatibility with 68XX SOCs.
+
+- interrupt-controller: This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>. The first cell is the bank within
+ the CIU and may have a value between 0 and 63. The second cell is
+ the bit within the bank and may also have a value between 0 and 63.
+
+Example:
+ interrupt-controller@1070100000000 {
+ compatible = "cavium,octeon-6880-ciu2";
+ interrupt-controller;
+ /* Interrupts are specified by two parts:
+ * 1) Controller register (0..63)
+ * 2) Bit within the register (0..63)
+ */
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x10701 0x00000000 0x0 0x4000000>;
+ };
diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
new file mode 100644
index 0000000000000000000000000000000000000000..cb4291e3b1d12be74a7124068142ca8ca06ce835
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
@@ -0,0 +1,21 @@
+* DMA Engine.
+
+The Octeon DMA Engine transfers between the Boot Bus and main memory.
+The DMA Engine will be refered to by phandle by any device that is
+connected to it.
+
+Properties:
+- compatible: "cavium,octeon-5750-bootbus-dma"
+
+ Compatibility with all cn52XX, cn56XX and cn6XXX SOCs.
+
+- reg: The base address of the DMA Engine's register bank.
+
+- interrupts: A single interrupt specifier.
+
+Example:
+ dma0: dma-engine@1180000000100 {
+ compatible = "cavium,octeon-5750-bootbus-dma";
+ reg = <0x11800 0x00000100 0x0 0x8>;
+ interrupts = <0 63>;
+ };
diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
new file mode 100644
index 0000000000000000000000000000000000000000..aa66b9b8d8013df6a0b175a8c6697ce4c8f5204c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
@@ -0,0 +1,46 @@
+* UCTL USB controller glue
+
+Properties:
+- compatible: "cavium,octeon-6335-uctl"
+
+ Compatibility with all cn6XXX SOCs.
+
+- reg: The base address of the UCTL register bank.
+
+- #address-cells: Must be <2>.
+
+- #size-cells: Must be <2>.
+
+- ranges: Empty to signify direct mapping of the children.
+
+- refclk-frequency: A single cell containing the reference clock
+ frequency in Hz.
+
+- refclk-type: A string describing the reference clock connection
+ either "crystal" or "external".
+
+Example:
+ uctl@118006f000000 {
+ compatible = "cavium,octeon-6335-uctl";
+ reg = <0x11800 0x6f000000 0x0 0x100>;
+ ranges; /* Direct mapping */
+ #address-cells = <2>;
+ #size-cells = <2>;
+ /* 12MHz, 24MHz and 48MHz allowed */
+ refclk-frequency = <24000000>;
+ /* Either "crystal" or "external" */
+ refclk-type = "crystal";
+
+ ehci@16f0000000000 {
+ compatible = "cavium,octeon-6335-ehci","usb-ehci";
+ reg = <0x16f00 0x00000000 0x0 0x100>;
+ interrupts = <0 56>;
+ big-endian-regs;
+ };
+ ohci@16f0000000400 {
+ compatible = "cavium,octeon-6335-ohci","usb-ohci";
+ reg = <0x16f00 0x00000400 0x0 0x100>;
+ interrupts = <0 56>;
+ big-endian-regs;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt
new file mode 100644
index 0000000000000000000000000000000000000000..04cb7491d23253555949bbcf7e48bf546cb118d0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt
@@ -0,0 +1,27 @@
+* System Management Interface (SMI) / MDIO
+
+Properties:
+- compatible: "cavium,octeon-3860-mdio"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the MDIO bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>. MDIO addresses have no size component.
+
+Typically an MDIO bus might have several children.
+
+Example:
+ mdio@1180000001800 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00001800 0x0 0x40>;
+
+ ethernet-phy@0 {
+ ...
+ reg = <0>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt
new file mode 100644
index 0000000000000000000000000000000000000000..5da628db68bf4eaf29fa0aa86d32500481da32fb
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mix.txt
@@ -0,0 +1,39 @@
+* MIX Ethernet controller.
+
+Properties:
+- compatible: "cavium,octeon-5750-mix"
+
+ Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
+ devices.
+
+- reg: The base addresses of four separate register banks. The first
+ bank contains the MIX registers. The second bank the corresponding
+ AGL registers. The third bank are the AGL registers shared by all
+ MIX devices present. The fourth bank is the AGL_PRT_CTL shared by
+ all MIX devices present.
+
+- cell-index: A single cell specifying which portion of the shared
+ register banks corresponds to this MIX device.
+
+- interrupts: Two interrupt specifiers. The first is the MIX
+ interrupt routing and the second the routing for the AGL interrupts.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+ if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+ ethernet@1070000100800 {
+ compatible = "cavium,octeon-5750-mix";
+ reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+ <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+ <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
+ <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */
+ cell-index = <1>;
+ interrupts = <1 18>, < 1 46>;
+ local-mac-address = [ 00 0f b7 10 63 54 ];
+ phy-handle = <&phy1>;
+ };
diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt
new file mode 100644
index 0000000000000000000000000000000000000000..d4c53ba04b3bad857d5f30c051c5e867653e31e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-pip.txt
@@ -0,0 +1,98 @@
+* PIP Ethernet nexus.
+
+The PIP Ethernet nexus can control several data packet input/output
+devices. The devices have a two level grouping scheme. There may be
+several interfaces, and each interface may have several ports. These
+ports might be an individual Ethernet PHY.
+
+
+Properties for the PIP nexus:
+- compatible: "cavium,octeon-3860-pip"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the PIP's register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP interfaces which is a child the PIP nexus:
+- compatible: "cavium,octeon-3860-pip-interface"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The interface number.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP port which is a child the PIP interface:
+- compatible: "cavium,octeon-3860-pip-port"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The port number within the interface group.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+ if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+
+ pip@11800a0000000 {
+ compatible = "cavium,octeon-3860-pip";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+ interface@0 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 60 ];
+ phy-handle = <&phy2>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 61 ];
+ phy-handle = <&phy3>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 62 ];
+ phy-handle = <&phy4>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 63 ];
+ phy-handle = <&phy5>;
+ };
+ };
+
+ interface@1 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 0f b7 10 63 64 ];
+ phy-handle = <&phy6>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/serial/cavium-uart.txt b/Documentation/devicetree/bindings/serial/cavium-uart.txt
new file mode 100644
index 0000000000000000000000000000000000000000..87a6c375cd44dbaee054d9994aaa47c3e04fe001
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/cavium-uart.txt
@@ -0,0 +1,19 @@
+* Universal Asynchronous Receiver/Transmitter (UART)
+
+- compatible: "cavium,octeon-3860-uart"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the UART register bank.
+
+- interrupts: A single interrupt specifier.
+
+- current-speed: Optional, the current bit rate in bits per second.
+
+Example:
+ uart1: serial@1180000000c00 {
+ compatible = "cavium,octeon-3860-uart","ns16550";
+ reg = <0x11800 0x00000c00 0x0 0x400>;
+ current-speed = <115200>;
+ interrupts = <0 35>;
+ };
diff --git a/arch/mips/cavium-octeon/.gitignore b/arch/mips/cavium-octeon/.gitignore
new file mode 100644
index 0000000000000000000000000000000000000000..39c968605ff63a3b451fa7ab9e86bc08030329e3
--- /dev/null
+++ b/arch/mips/cavium-octeon/.gitignore
@@ -0,0 +1,2 @@
+*.dtb.S
+*.dtb
diff --git a/arch/mips/cavium-octeon/Makefile b/arch/mips/cavium-octeon/Makefile
index 19eb0434269ffc6017bb79da7f00485d2cb13813..1e37522cc21ff6a5f644ebe1386c8b6525680f6d 100644
--- a/arch/mips/cavium-octeon/Makefile
+++ b/arch/mips/cavium-octeon/Makefile
@@ -15,3 +15,16 @@ obj-y += octeon-memcpy.o
obj-y += executive/
obj-$(CONFIG_SMP) += smp.o
+
+DTS_FILES = octeon_3xxx.dts octeon_68xx.dts
+DTB_FILES = $(patsubst %.dts, %.dtb, $(DTS_FILES))
+
+obj-y += $(patsubst %.dts, %.dtb.o, $(DTS_FILES))
+
+$(obj)/%.dtb: $(src)/%.dts FORCE
+ $(call if_changed_dep,dtc)
+
+# Let's keep the .dtb files around in case we want to look at them.
+.SECONDARY: $(addprefix $(obj)/, $(DTB_FILES))
+
+clean-files += $(DTB_FILES) $(patsubst %.dtb, %.dtb.S, $(DTB_FILES))
diff --git a/arch/mips/cavium-octeon/octeon_3xxx.dts b/arch/mips/cavium-octeon/octeon_3xxx.dts
new file mode 100644
index 0000000000000000000000000000000000000000..f28b2d0fde2226e5c73da4bc6029460a88886bcd
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon_3xxx.dts
@@ -0,0 +1,571 @@
+/dts-v1/;
+/*
+ * OCTEON 3XXX, 5XXX, 63XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use. Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+ compatible = "cavium,octeon-3860";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&ciu>;
+
+ soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges; /* Direct mapping */
+
+ ciu: interrupt-controller@1070000000000 {
+ compatible = "cavium,octeon-3860-ciu";
+ interrupt-controller;
+ /* Interrupts are specified by two parts:
+ * 1) Controller register (0 or 1)
+ * 2) Bit within the register (0..63)
+ */
+ #interrupt-cells = <2>;
+ reg = <0x10700 0x00000000 0x0 0x7000>;
+ };
+
+ gpio: gpio-controller@1070000000800 {
+ #gpio-cells = <2>;
+ compatible = "cavium,octeon-3860-gpio";
+ reg = <0x10700 0x00000800 0x0 0x100>;
+ gpio-controller;
+ /* Interrupts are specified by two parts:
+ * 1) GPIO pin number (0..15)
+ * 2) Triggering (1 - edge rising
+ * 2 - edge falling
+ * 4 - level active high
+ * 8 - level active low)
+ */
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ /* The GPIO pin connect to 16 consecutive CUI bits */
+ interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+ <0 20>, <0 21>, <0 22>, <0 23>,
+ <0 24>, <0 25>, <0 26>, <0 27>,
+ <0 28>, <0 29>, <0 30>, <0 31>;
+ };
+
+ smi0: mdio@1180000001800 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00001800 0x0 0x40>;
+
+ phy0: ethernet-phy@0 {
+ compatible = "marvell,88e1118";
+ marvell,reg-init =
+ /* Fix rx and tx clock transition timing */
+ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+ /* Adjust LED drive. */
+ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+ /* irq, blink-activity, blink-link */
+ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ compatible = "marvell,88e1118";
+ marvell,reg-init =
+ /* Fix rx and tx clock transition timing */
+ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+ /* Adjust LED drive. */
+ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+ /* irq, blink-activity, blink-link */
+ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+ reg = <1>;
+ };
+
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+
+ phy6: ethernet-phy@6 {
+ reg = <6>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy7: ethernet-phy@7 {
+ reg = <7>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy8: ethernet-phy@8 {
+ reg = <8>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy9: ethernet-phy@9 {
+ reg = <9>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ };
+
+ smi1: mdio@1180000001900 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00001900 0x0 0x40>;
+
+ phy100: ethernet-phy@1 {
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy101: ethernet-phy@2 {
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy102: ethernet-phy@3 {
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ phy103: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ };
+ };
+
+ mix0: ethernet@1070000100000 {
+ compatible = "cavium,octeon-5750-mix";
+ reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+ <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+ <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
+ <0x11800 0xE0002000 0x0 0x8>; /* AGL_PRT_CTL */
+ cell-index = <0>;
+ interrupts = <0 62>, <1 46>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy0>;
+ };
+
+ mix1: ethernet@1070000100800 {
+ compatible = "cavium,octeon-5750-mix";
+ reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+ <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+ <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
+ <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */
+ cell-index = <1>;
+ interrupts = <1 18>, < 1 46>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy1>;
+ };
+
+ pip: pip@11800a0000000 {
+ compatible = "cavium,octeon-3860-pip";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+ interface@0 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy2>;
+ cavium,alt-phy-handle = <&phy100>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy3>;
+ cavium,alt-phy-handle = <&phy101>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy4>;
+ cavium,alt-phy-handle = <&phy102>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy5>;
+ cavium,alt-phy-handle = <&phy103>;
+ };
+ ethernet@4 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x4>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@5 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x5>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@6 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x6>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@7 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x7>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@8 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x8>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@9 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x9>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@a {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0xa>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@b {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0xb>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@c {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0xc>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@d {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0xd>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@e {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0xe>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ ethernet@f {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0xf>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+
+ interface@1 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy6>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy7>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy8>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy9>;
+ };
+ };
+ };
+
+ twsi0: i2c@1180000001000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cavium,octeon-3860-twsi";
+ reg = <0x11800 0x00001000 0x0 0x200>;
+ interrupts = <0 45>;
+ clock-frequency = <100000>;
+
+ rtc@68 {
+ compatible = "dallas,ds1337";
+ reg = <0x68>;
+ };
+ tmp@4c {
+ compatible = "ti,tmp421";
+ reg = <0x4c>;
+ };
+ };
+
+ twsi1: i2c@1180000001200 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cavium,octeon-3860-twsi";
+ reg = <0x11800 0x00001200 0x0 0x200>;
+ interrupts = <0 59>;
+ clock-frequency = <100000>;
+ };
+
+ uart0: serial@1180000000800 {
+ compatible = "cavium,octeon-3860-uart","ns16550";
+ reg = <0x11800 0x00000800 0x0 0x400>;
+ clock-frequency = <0>;
+ current-speed = <115200>;
+ reg-shift = <3>;
+ interrupts = <0 34>;
+ };
+
+ uart1: serial@1180000000c00 {
+ compatible = "cavium,octeon-3860-uart","ns16550";
+ reg = <0x11800 0x00000c00 0x0 0x400>;
+ clock-frequency = <0>;
+ current-speed = <115200>;
+ reg-shift = <3>;
+ interrupts = <0 35>;
+ };
+
+ uart2: serial@1180000000400 {
+ compatible = "cavium,octeon-3860-uart","ns16550";
+ reg = <0x11800 0x00000400 0x0 0x400>;
+ clock-frequency = <0>;
+ current-speed = <115200>;
+ reg-shift = <3>;
+ interrupts = <1 16>;
+ };
+
+ bootbus: bootbus@1180000000000 {
+ compatible = "cavium,octeon-3860-bootbus";
+ reg = <0x11800 0x00000000 0x0 0x200>;
+ /* The chip select number and offset */
+ #address-cells = <2>;
+ /* The size of the chip select region */
+ #size-cells = <1>;
+ ranges = <0 0 0x0 0x1f400000 0xc00000>,
+ <1 0 0x10000 0x30000000 0>,
+ <2 0 0x10000 0x40000000 0>,
+ <3 0 0x10000 0x50000000 0>,
+ <4 0 0x0 0x1d020000 0x10000>,
+ <5 0 0x0 0x1d040000 0x10000>,
+ <6 0 0x0 0x1d050000 0x10000>,
+ <7 0 0x10000 0x90000000 0>;
+
+ cavium,cs-config@0 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <0>;
+ cavium,t-adr = <20>;
+ cavium,t-ce = <60>;
+ cavium,t-oe = <60>;
+ cavium,t-we = <45>;
+ cavium,t-rd-hld = <35>;
+ cavium,t-wr-hld = <45>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <0>;
+ cavium,t-page = <35>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <8>;
+ };
+ cavium,cs-config@4 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <4>;
+ cavium,t-adr = <320>;
+ cavium,t-ce = <320>;
+ cavium,t-oe = <320>;
+ cavium,t-we = <320>;
+ cavium,t-rd-hld = <320>;
+ cavium,t-wr-hld = <320>;
+ cavium,t-pause = <320>;
+ cavium,t-wait = <320>;
+ cavium,t-page = <320>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <8>;
+ };
+ cavium,cs-config@5 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <5>;
+ cavium,t-adr = <5>;
+ cavium,t-ce = <300>;
+ cavium,t-oe = <125>;
+ cavium,t-we = <150>;
+ cavium,t-rd-hld = <100>;
+ cavium,t-wr-hld = <30>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <30>;
+ cavium,t-page = <320>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <16>;
+ };
+ cavium,cs-config@6 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <6>;
+ cavium,t-adr = <5>;
+ cavium,t-ce = <300>;
+ cavium,t-oe = <270>;
+ cavium,t-we = <150>;
+ cavium,t-rd-hld = <100>;
+ cavium,t-wr-hld = <70>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <0>;
+ cavium,t-page = <320>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,wait-mode;
+ cavium,bus-width = <16>;
+ };
+
+ flash0: nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ led0: led-display@4,0 {
+ compatible = "avago,hdsp-253x";
+ reg = <4 0x20 0x20>, <4 0 0x20>;
+ };
+
+ cf0: compact-flash@5,0 {
+ compatible = "cavium,ebt3000-compact-flash";
+ reg = <5 0 0x10000>, <6 0 0x10000>;
+ cavium,bus-width = <16>;
+ cavium,true-ide;
+ cavium,dma-engine-handle = <&dma0>;
+ };
+ };
+
+ dma0: dma-engine@1180000000100 {
+ compatible = "cavium,octeon-5750-bootbus-dma";
+ reg = <0x11800 0x00000100 0x0 0x8>;
+ interrupts = <0 63>;
+ };
+ dma1: dma-engine@1180000000108 {
+ compatible = "cavium,octeon-5750-bootbus-dma";
+ reg = <0x11800 0x00000108 0x0 0x8>;
+ interrupts = <0 63>;
+ };
+
+ uctl: uctl@118006f000000 {
+ compatible = "cavium,octeon-6335-uctl";
+ reg = <0x11800 0x6f000000 0x0 0x100>;
+ ranges; /* Direct mapping */
+ #address-cells = <2>;
+ #size-cells = <2>;
+ /* 12MHz, 24MHz and 48MHz allowed */
+ refclk-frequency = <12000000>;
+ /* Either "crystal" or "external" */
+ refclk-type = "crystal";
+
+ ehci@16f0000000000 {
+ compatible = "cavium,octeon-6335-ehci","usb-ehci";
+ reg = <0x16f00 0x00000000 0x0 0x100>;
+ interrupts = <0 56>;
+ big-endian-regs;
+ };
+ ohci@16f0000000400 {
+ compatible = "cavium,octeon-6335-ohci","usb-ohci";
+ reg = <0x16f00 0x00000400 0x0 0x100>;
+ interrupts = <0 56>;
+ big-endian-regs;
+ };
+ };
+ };
+
+ aliases {
+ mix0 = &mix0;
+ mix1 = &mix1;
+ pip = &pip;
+ smi0 = &smi0;
+ smi1 = &smi1;
+ twsi0 = &twsi0;
+ twsi1 = &twsi1;
+ uart0 = &uart0;
+ uart1 = &uart1;
+ uart2 = &uart2;
+ flash0 = &flash0;
+ cf0 = &cf0;
+ uctl = &uctl;
+ led0 = &led0;
+ };
+ };
diff --git a/arch/mips/cavium-octeon/octeon_68xx.dts b/arch/mips/cavium-octeon/octeon_68xx.dts
new file mode 100644
index 0000000000000000000000000000000000000000..1839468932b68a8964eb96b36afcd0e4e64976b5
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon_68xx.dts
@@ -0,0 +1,625 @@
+/dts-v1/;
+/*
+ * OCTEON 68XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use. Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+ compatible = "cavium,octeon-6880";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&ciu2>;
+
+ soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges; /* Direct mapping */
+
+ ciu2: interrupt-controller@1070100000000 {
+ compatible = "cavium,octeon-6880-ciu2";
+ interrupt-controller;
+ /* Interrupts are specified by two parts:
+ * 1) Controller register (0 or 7)
+ * 2) Bit within the register (0..63)
+ */
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x10701 0x00000000 0x0 0x4000000>;
+ };
+
+ gpio: gpio-controller@1070000000800 {
+ #gpio-cells = <2>;
+ compatible = "cavium,octeon-3860-gpio";
+ reg = <0x10700 0x00000800 0x0 0x100>;
+ gpio-controller;
+ /* Interrupts are specified by two parts:
+ * 1) GPIO pin number (0..15)
+ * 2) Triggering (1 - edge rising
+ * 2 - edge falling
+ * 4 - level active high
+ * 8 - level active low)
+ */
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ /* The GPIO pins connect to 16 consecutive CUI bits */
+ interrupts = <7 0>, <7 1>, <7 2>, <7 3>,
+ <7 4>, <7 5>, <7 6>, <7 7>,
+ <7 8>, <7 9>, <7 10>, <7 11>,
+ <7 12>, <7 13>, <7 14>, <7 15>;
+ };
+
+ smi0: mdio@1180000003800 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00003800 0x0 0x40>;
+
+ phy0: ethernet-phy@6 {
+ compatible = "marvell,88e1118";
+ marvell,reg-init =
+ /* Fix rx and tx clock transition timing */
+ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+ /* Adjust LED drive. */
+ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+ /* irq, blink-activity, blink-link */
+ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+ reg = <6>;
+ };
+
+ phy1: ethernet-phy@1 {
+ cavium,qlm-trim = "4,sgmii";
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy2: ethernet-phy@2 {
+ cavium,qlm-trim = "4,sgmii";
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy3: ethernet-phy@3 {
+ cavium,qlm-trim = "4,sgmii";
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy4: ethernet-phy@4 {
+ cavium,qlm-trim = "4,sgmii";
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ };
+
+ smi1: mdio@1180000003880 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00003880 0x0 0x40>;
+
+ phy41: ethernet-phy@1 {
+ cavium,qlm-trim = "0,sgmii";
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy42: ethernet-phy@2 {
+ cavium,qlm-trim = "0,sgmii";
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy43: ethernet-phy@3 {
+ cavium,qlm-trim = "0,sgmii";
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy44: ethernet-phy@4 {
+ cavium,qlm-trim = "0,sgmii";
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ };
+
+ smi2: mdio@1180000003900 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00003900 0x0 0x40>;
+
+ phy21: ethernet-phy@1 {
+ cavium,qlm-trim = "2,sgmii";
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy22: ethernet-phy@2 {
+ cavium,qlm-trim = "2,sgmii";
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy23: ethernet-phy@3 {
+ cavium,qlm-trim = "2,sgmii";
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy24: ethernet-phy@4 {
+ cavium,qlm-trim = "2,sgmii";
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ };
+
+ smi3: mdio@1180000003980 {
+ compatible = "cavium,octeon-3860-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0x00003980 0x0 0x40>;
+
+ phy11: ethernet-phy@1 {
+ cavium,qlm-trim = "3,sgmii";
+ reg = <1>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy12: ethernet-phy@2 {
+ cavium,qlm-trim = "3,sgmii";
+ reg = <2>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy13: ethernet-phy@3 {
+ cavium,qlm-trim = "3,sgmii";
+ reg = <3>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ phy14: ethernet-phy@4 {
+ cavium,qlm-trim = "3,sgmii";
+ reg = <4>;
+ compatible = "marvell,88e1149r";
+ marvell,reg-init = <3 0x10 0 0x5777>,
+ <3 0x11 0 0x00aa>,
+ <3 0x12 0 0x4105>,
+ <3 0x13 0 0x0a60>;
+ };
+ };
+
+ mix0: ethernet@1070000100000 {
+ compatible = "cavium,octeon-5750-mix";
+ reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+ <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+ <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
+ <0x11800 0xE0002000 0x0 0x8>; /* AGL_PRT_CTL */
+ cell-index = <0>;
+ interrupts = <6 40>, <6 32>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy0>;
+ };
+
+ pip: pip@11800a0000000 {
+ compatible = "cavium,octeon-3860-pip";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+ interface@4 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy1>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy2>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy3>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy4>;
+ };
+ };
+
+ interface@3 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy11>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy12>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy13>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy14>;
+ };
+ };
+
+ interface@2 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy21>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy22>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy23>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy24>;
+ };
+ };
+
+ interface@1 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+
+ interface@0 {
+ compatible = "cavium,octeon-3860-pip-interface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>; /* interface */
+
+ ethernet@0 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x0>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy41>;
+ };
+ ethernet@1 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x1>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy42>;
+ };
+ ethernet@2 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x2>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy43>;
+ };
+ ethernet@3 {
+ compatible = "cavium,octeon-3860-pip-port";
+ reg = <0x3>; /* Port */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&phy44>;
+ };
+ };
+ };
+
+ twsi0: i2c@1180000001000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cavium,octeon-3860-twsi";
+ reg = <0x11800 0x00001000 0x0 0x200>;
+ interrupts = <3 32>;
+ clock-frequency = <100000>;
+
+ rtc@68 {
+ compatible = "dallas,ds1337";
+ reg = <0x68>;
+ };
+ tmp@4c {
+ compatible = "ti,tmp421";
+ reg = <0x4c>;
+ };
+ };
+
+ twsi1: i2c@1180000001200 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cavium,octeon-3860-twsi";
+ reg = <0x11800 0x00001200 0x0 0x200>;
+ interrupts = <3 33>;
+ clock-frequency = <100000>;
+ };
+
+ uart0: serial@1180000000800 {
+ compatible = "cavium,octeon-3860-uart","ns16550";
+ reg = <0x11800 0x00000800 0x0 0x400>;
+ clock-frequency = <0>;
+ current-speed = <115200>;
+ reg-shift = <3>;
+ interrupts = <3 36>;
+ };
+
+ uart1: serial@1180000000c00 {
+ compatible = "cavium,octeon-3860-uart","ns16550";
+ reg = <0x11800 0x00000c00 0x0 0x400>;
+ clock-frequency = <0>;
+ current-speed = <115200>;
+ reg-shift = <3>;
+ interrupts = <3 37>;
+ };
+
+ bootbus: bootbus@1180000000000 {
+ compatible = "cavium,octeon-3860-bootbus";
+ reg = <0x11800 0x00000000 0x0 0x200>;
+ /* The chip select number and offset */
+ #address-cells = <2>;
+ /* The size of the chip select region */
+ #size-cells = <1>;
+ ranges = <0 0 0 0x1f400000 0xc00000>,
+ <1 0 0x10000 0x30000000 0>,
+ <2 0 0x10000 0x40000000 0>,
+ <3 0 0x10000 0x50000000 0>,
+ <4 0 0 0x1d020000 0x10000>,
+ <5 0 0 0x1d040000 0x10000>,
+ <6 0 0 0x1d050000 0x10000>,
+ <7 0 0x10000 0x90000000 0>;
+
+ cavium,cs-config@0 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <0>;
+ cavium,t-adr = <10>;
+ cavium,t-ce = <50>;
+ cavium,t-oe = <50>;
+ cavium,t-we = <35>;
+ cavium,t-rd-hld = <25>;
+ cavium,t-wr-hld = <35>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <300>;
+ cavium,t-page = <25>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <8>;
+ };
+ cavium,cs-config@4 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <4>;
+ cavium,t-adr = <320>;
+ cavium,t-ce = <320>;
+ cavium,t-oe = <320>;
+ cavium,t-we = <320>;
+ cavium,t-rd-hld = <320>;
+ cavium,t-wr-hld = <320>;
+ cavium,t-pause = <320>;
+ cavium,t-wait = <320>;
+ cavium,t-page = <320>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <8>;
+ };
+ cavium,cs-config@5 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <5>;
+ cavium,t-adr = <0>;
+ cavium,t-ce = <300>;
+ cavium,t-oe = <125>;
+ cavium,t-we = <150>;
+ cavium,t-rd-hld = <100>;
+ cavium,t-wr-hld = <300>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <300>;
+ cavium,t-page = <310>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,bus-width = <16>;
+ };
+ cavium,cs-config@6 {
+ compatible = "cavium,octeon-3860-bootbus-config";
+ cavium,cs-index = <6>;
+ cavium,t-adr = <0>;
+ cavium,t-ce = <30>;
+ cavium,t-oe = <125>;
+ cavium,t-we = <150>;
+ cavium,t-rd-hld = <100>;
+ cavium,t-wr-hld = <30>;
+ cavium,t-pause = <0>;
+ cavium,t-wait = <30>;
+ cavium,t-page = <310>;
+ cavium,t-rd-dly = <0>;
+
+ cavium,pages = <0>;
+ cavium,wait-mode;
+ cavium,bus-width = <16>;
+ };
+
+ flash0: nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bootloader";
+ reg = <0 0x200000>;
+ read-only;
+ };
+ partition@200000 {
+ label = "kernel";
+ reg = <0x200000 0x200000>;
+ };
+ partition@400000 {
+ label = "cramfs";
+ reg = <0x400000 0x3fe000>;
+ };
+ partition@7fe000 {
+ label = "environment";
+ reg = <0x7fe000 0x2000>;
+ read-only;
+ };
+ };
+
+ led0: led-display@4,0 {
+ compatible = "avago,hdsp-253x";
+ reg = <4 0x20 0x20>, <4 0 0x20>;
+ };
+
+ compact-flash@5,0 {
+ compatible = "cavium,ebt3000-compact-flash";
+ reg = <5 0 0x10000>, <6 0 0x10000>;
+ cavium,bus-width = <16>;
+ cavium,true-ide;
+ cavium,dma-engine-handle = <&dma0>;
+ };
+ };
+
+ dma0: dma-engine@1180000000100 {
+ compatible = "cavium,octeon-5750-bootbus-dma";
+ reg = <0x11800 0x00000100 0x0 0x8>;
+ interrupts = <0 63>;
+ };
+ dma1: dma-engine@1180000000108 {
+ compatible = "cavium,octeon-5750-bootbus-dma";
+ reg = <0x11800 0x00000108 0x0 0x8>;
+ interrupts = <0 63>;
+ };
+
+ uctl: uctl@118006f000000 {
+ compatible = "cavium,octeon-6335-uctl";
+ reg = <0x11800 0x6f000000 0x0 0x100>;
+ ranges; /* Direct mapping */
+ #address-cells = <2>;
+ #size-cells = <2>;
+ /* 12MHz, 24MHz and 48MHz allowed */
+ refclk-frequency = <12000000>;
+ /* Either "crystal" or "external" */
+ refclk-type = "crystal";
+
+ ehci@16f0000000000 {
+ compatible = "cavium,octeon-6335-ehci","usb-ehci";
+ reg = <0x16f00 0x00000000 0x0 0x100>;
+ interrupts = <3 44>;
+ big-endian-regs;
+ };
+ ohci@16f0000000400 {
+ compatible = "cavium,octeon-6335-ohci","usb-ohci";
+ reg = <0x16f00 0x00000400 0x0 0x100>;
+ interrupts = <3 44>;
+ big-endian-regs;
+ };
+ };
+ };
+
+ aliases {
+ mix0 = &mix0;
+ pip = &pip;
+ smi0 = &smi0;
+ smi1 = &smi1;
+ smi2 = &smi2;
+ smi3 = &smi3;
+ twsi0 = &twsi0;
+ twsi1 = &twsi1;
+ uart0 = &uart0;
+ uart1 = &uart1;
+ uctl = &uctl;
+ led0 = &led0;
+ flash0 = &flash0;
+ };
+ };